Filter
Top Products
100 En
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Zone 2 amplifier ZONE2 AMP
Zone 3 amplifier ZONE3 AMP
Use to select how the ZONE 2 and/or ZONE 3 speakers
are amplified.
Choices: EXT, [SP1], [SP2], BOTH
• Select “EXT” if you want to connect your Zone 2 or
Zone 3 speakers through an external amplifier
connected to the ZONE 2 OUTPUT or ZONE 3
OUTPUT jacks on the rear panel of this unit.
• Select “[SP1]” to use the internal surround back
amplifier of this unit when you want to connect your
Zone 2 or Zone 3 speakers directly to the SP1 speaker
terminals on the rear panel of this unit.
• Select “[SP2]” to use the internal surround amplifier of
this unit when you want to connect your Zone 2 or
Zone 3 speakers directly to the SP2 speaker terminals
on the rear panel of this unit.
• Select “BOTH” to use the internal surround and
surround back amplifiers of this unit when you want to
connect your Zone 2 or Zone 3 speakers directly to
both the SP1 and the SP2 speaker terminals on the rear
panel of this unit.
• When “BI-AMP” is set to “ON” in the “ADVANCED SETUP”
menu, “[SP1]”, “[SP2]” and “BOTH” cannot be selected.
• When “BOTH” is selected for “ZONE2 AMP”, only “EXT” can
be selected for “ZONE3 AMP”.
• When “BOTH” is selected for “ZONE3 AMP”, only “EXT” can
be selected for “ZONE2 AMP”.
• When you set “ZONE2 AMP” or “ZONE3 AMP” to “[SP1]” or
“[SP2]” and the corresponding zone is turned on, no sound is
output from the surround back speakers.
• When you set “ZONE2 AMP” or “ZONE3 AMP” to “BOTH”
and the corresponding zone is turned on, no sound is output
from both the surround speakers and the surround back speakers
in the main zone.
• When both “ZONE2 AMP” and “ZONE3 AMP” are set to
“[SP1]” or “[SP2]” and Zone 2 and Zone 3 are turned on, no
sound is output from both the surround speakers and the
surround back speakers in the main zone.
• When you use internal amplifiers for Zone 2 or Zone 3, some
surround field programs may not work in the same way as when
you do not use the internal amplifiers for Zone 2 or Zone 3.
■ XM Radio setting G)XM RADIO SET
(U.S.A. and Canada models only)
XM Radio antenna XM ANTENNA
Use this feature to check the current reception level of the
XM Passport System connected to the XM jack of this
unit (see page 61). For the best reception, orient the XM
Passport System so that a value of 60% or more is
displayed here.
Display status: NONE, 0 to 100%
•
“NONE” is displayed if the XM Passport System is not connected to
this unit. In this case, check the antenna connections (see page 61).
• The “XM ANTENNA” parameter cannot be adjusted by using
the remote control. Instead, you need to adjust the orientation of
the XM Passport System connected to the XM jack of this unit
for a better percentage of the reception level.
■ Dock set H)DOCK SET
Charge on standby STANDBY CHRG
Use this feature to select whether this unit charges the
battery of the stationed iPod or not when this unit is in the
standby mode (see page 73).
Choices: AUTO, OFF
• Select “AUTO” to charge the battery of the stationed
iPod when this unit is turned on and in the standby
mode.
• Select “OFF” to charge the battery of the stationed
iPod only when this unit is turned on.
Notes
Notes
G)XM RADIO SET
.XM ANTENNA;;NONE
H)DOCK SET
.STANDBYCHRG;AUTO
[]/[]:Select
[ENTER]:Return
)
)
01EN_00_RX-V1700_U.book Page 100 Tuesday, June 27, 2006 9:37 AM