Filter
Top Products
Using other functions
10
68
En
• Note that the setting you make here is stored in
memory, even if you switch off the receiver, so if you
want to record a different input source later, you
must do so with
REC SELECT
, or by selecting
RECOUT SOURCE
.
3 After RECOUT disappears from the display, select
the input source you want to listen to.
This will be heard from the main system without affecting
your recording.
1
Tip
• If you have a digital recorder connected to the
DIGITAL OUT1
(
ROOM3
) digital output and
ROOM
3
is switched on (see
Using the multi-room controls
on page 59), you can also select a different input
source for this output while
ROOM 3
shows in the
display.
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if you find
the that the
OVER
indicator is lights often, or you can
hear distortion in the sound.
2
• Press ANALOG ATT to switch the input attenuator
on or off.
Watching video and audio sources
independently
You can listen to a sound source and select a different
video source on your TV.
• While listening to a source, press VIDEO SEL (
VIDEO
SELECT
) to select the video source you want to watch.
Press repeatedly to cycle through the possible video
sources. You can select
DVD
,
TV
,
SAT
,
DVR1
,
DVR2
,
VIDEO1
,
VIDEO2
or
OFF
(no video signal).
3
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
• Press
SLEEP
repeatedly to set the sleep time.
• You can check the remaining sleep time at any time
by pressing
SLEEP
once. Pressing repeatedly will
cycle through the sleep options again.
4
Dimming the display
You can choose between four brightness levels for the
front panel display. Note that when selecting sources,
the display automatically brightens for a few seconds.
• Press DIMMER repeatedly to change the brightness
of the front panel display.
Switching the speaker impedance
We recommend using speakers of 8
Ω
with this system,
but it is possible to switch the impedance setting if you
plan to use speakers with a 6
Ω
impedance rating.
• With the receiver in standby, press
STANDBY/
ON
while holding down the
SPEAKERS
button.
Each time you do this, you switch between the
impedance settings:
•
SP 6 OHM
– Use this setting if your speakers are
rated at 6
Ω
.
•
SP 8 OHM
– Use this setting if your speakers are
rated at 8
Ω
or more.
Note
1• Note that switching the
ROOM 2
input source (as explained in
Multi-room listening
on page 57) also changes the
RECOUT
input source.
• If
RECOUT SOURCE
is selected, changing the input source likewise changes the input source used for your recording.
2 The attenuator isn’t available with digital sources, or when using the Stream Direct modes.
3 Note that this feature will not work with video sources assigned to either of the HDMI video inputs.
SLEEP
10
SR
+
ANALOG
ATT
SC
VIDEO
SEL
DIMMER
S.RETRIEVER
CLASS
D.ACCESS
SLEEP
+
10
SR
+
ANALOG
ATT
DISC
VIDEO
SEL
DIMMER
S.RETRIEVER
CLASS
D.ACCESS
4 You can also switch off the sleep timer simply by switching off the receiver.
SLEEP
SR
+
ANALOG
ATT
VIDEO
SEL
DIMMER
S.RETRIEVER
CLASS
DACCESS
Off
30 min 60 min
90 min
SLEEP
0
SR
+
ANALOG
ATT
VIDEO
SEL
DIMMER
S.RETRIEVER
CLASS
D.ACC ES S
VSX_84TXSi.book.fm 68 ページ ２００６年３月１３日 月曜日 午前１１時５４分