Filter
Top Products
Using other functions
10
66
En
Chapter 10
Using other functions
Setting the AV options
There are a number of additional sound and picture
settings you can make using the AV Parameter menu.
The defaults, if not stated, are listed in bold.
Important
• Note that if a setting doesn’t appear in the AV
Parameter menu, it is unavailable due to the current
source, settings and status of the receiver.
1 Press
AV PARAMETER
.
2 Use
/
to select the setting you want to adjust.
Depending on the current status / mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
3 Use
/
to set it as necessary.
See the table below for the options available for each
setting.
4 Press
RETURN
to confirm and exit the menu.
Setting What it does Option(s)
Midnight
Allows you to hear effective surround
sound of movies at low volumes.
MID/LDN OFF
MIDNIGHT ON
Loudness
Used to get good bass and treble
from music sources at low volumes.
LOUDNESS ON
Tone
control
Applies the treble and bass tone
controls to a source, or bypasses
them completely.
BYPASS
ON
Bass
Adjusts the amount of bass. –6 to +6 (dB)
default:
0
(dB)
Treble
Adjusts the amount of treble. –6 to +6 (dB)
default:
0
(dB)
Center
Width
a
(Applicable
only when
using a center
speaker)
Provides a better blend of the front
speakers by spreading the center
channel between the front right and
left speakers, making it sound wider
(higher settings) or narrower (lower
settings).
0 to 7
Default:
3
Dimension
b
Adjusts the depth of the surround
sound balance from front to back,
making the sound more distant
(minus settings), or more forward
(positive settings).
–3 to +3
Default:
0
Panorama
b
Extends the front stereo image to
include the surround speakers for a
‘wraparound’ effect.
OFF
ON
Center
Image
b
(Applicable
only when
using a center
speaker)
Adjusts the center image to create a
wider stereo effect with vocals.
Adjust the effect from
0
(all center
channel sent to front right and left
speakers) to
10
(center channel sent
to the center speaker only).
0 to 10
Default:
3
Effect
Sets the effect level for the currently
selected Advanced Surround mode
(each mode can be set separately).
10 to 90
High Bit /
High
Sampling
Creates a wider dynamic range with
digital sources like CDs or DVDs.
OFF
ON
Digital
Noise
Reduction
(DNR)
May improve the quality of sound in a
noisy source (for example, cassette
or video tape with lots of background
noise) when switched on.
OFF
ON
Dual Mono
Specifies how dual mono encoded
Dolby Digital and DTS soundtracks
should be played. Dual mono is not
widely used, but is sometimes
necessary when two languages need
to be sent to separate channels.
CH1
– Channel
1 is heard only
CH2
– Channel
2 is heard only
CH1 CH2
–
Both channels
heard from
front speakers
Dynamic
Range
Control
(DRC)
Specifies the amount of dynamic
range adjustment to Dolby Digital
and DTS movie soundtracks (you
may want to use this when listening
to surround sound at low volumes).
OFF
MAX
MID
Dialog
Enhance-
ment
a
Localizes dialog in the center
channel to make it stand out from
other background sounds in a TV or
movie soundtrack.
OFF
ON
SACD Gain
c
Brings out detail in SACDs by
maximizing the dynamic range
(during digital processing).
0 to 6 (dB)
default:
0
(dB)
Sound
Delay
Some monitors have a slight delay
when showing video, so the
soundtrack will be slightly out of sync
with the picture. By adding a bit of
delay, you can adjust the sound to
match the presentation of the video.
0.0 to 6.0
(frames)
1 second = 30
frames (NTSC)
HDMI
d
Specifies the routing of the HDMI
audio signal out of this receiver (
amp
)
or
through
to a TV or plasma display.
AMP
THROUGH
Digital
Video
Conversion
Converts video signals for output
from the
MONITOR OUT
jacks for all
video types.
ON
OFF
Brightness
Adjusts the overall brightness. –10 to +10
default:
0
Setting
What it does Option(s)
VSX_84TXSi.book.fm 66 ページ ２００６年３月１３日 月曜日 午前１１時５４分