Filter
Top Products
Using the tuner
06
33
En
Saving station presets
If you often listen to a particular radio station, it's
convenient to have the receiver store the frequency for
easy recall whenever you want to listen to that station.
This saves the effort of manually tuning in each time. This
receiver can memorize up to 30 stations, stored in three
banks, or classes, (A, B and C) of 10 stations each. When
saving an FM frequency, the
MPX
setting (see page 32) is
also stored.
1 Tune to a station you want to memorize.
See
Listening to the radio
on page 32 for more on this.
2 Press T.EDIT (TUNER EDIT).
The display shows
STATION MEMORY
, then a blinking
memory class.
3 Press CLASS to select one of the three classes then
press ST
/
to select the station preset you want.
You can also use the number buttons to select a station
preset.
4 Press
ENTER
.
After pressing
ENTER
, the preset class and number stop
blinking and the receiver stores the station.
Naming station presets
For easier identification, you can name your station
presets.
1 Choose the station preset you want to name.
See
Listening to station presets
below for how to do this.
2 Press T.EDIT (TUNER EDIT).
The display shows
STATION NAME
, then a blinking
cursor at the first character position.
3 Input the name you want.
Choose from the following characters for a name up to
four characters long.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
0123456789
!”#$%&’()
∗
+,–./:;<=>?@[ \ ]^_{|} ˜
• Use the
ST
/
buttons (remote) to select
characters.
• Press
ENTER
to confirm a character. If no character
is input, a space is input.
• The name is stored when
ENTER
is pressed after
choosing the fourth character.
Tip
• To erase a station name, simply repeat steps 1-3 and
input four spaces instead of a name.
• Once you have named a station preset, you can press
DISP
when listening to a station to switch the display
between name and frequency.
Listening to station presets
You will need to have some presets stored to do this. See
Saving station presets
above if you haven’t done this
already.
1 Press
TUNER
to select the tuner.
2 Press CLASS to select the class in which the station
is stored.
Press repeatedly to cycle through classes A, B and C.
3 Press ST
/
to select the station preset you want.
• You can also use the number buttons on the remote
control to recall the station preset.
SLEEP
ANALOG
AT T
VIDEO
SEL
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
DVD SAT
VIDEO 1 T V CONT
DVR1 i Pod
TUNER
RECEIVER
CD
DVR2
CD-R
TV VIDEO 2
XM RADIO
ROOM2/3
+
10
DISC
CLASS
D.ACCESS
ENTER
TV CONTROL
VOL
TUNE
TUNE
ST ST
TV CH
INPUT
SELECT
DTV INFO
MUTE
REC
TV VOL
ENTER
ENTER
AV PARAMETER
TOP MENU ì
DTV MENU
CH LEVEL
MENU
T.EDIT
BAND
GUIDE
RETURN
SETUP
CATEGORY
ì
SHIFT
STATUS
MCACC S.DIRECT
MULTI OPE
SIGNAL SEL
PHOTO
SBch
STEREO
MEMORY
MPX
AUDIO SUBTITLE
ADV. SURR
STANDARD
PHASE
THX
ENTER
REC STOP
HDD
CH
CH
DVD
DISP
RECEIVER
VSX_84TXSi.book.fm 33 ページ ２００６年３月１３日 月曜日 午前１１時５４分