Pioneer CDJ-1000MK2 CD Player User Manual


 
30
<DRB1338>
En/Fr
7 Data other than CUE/LOOP stored on MMC
Hot cue points A, B, C
Hot cue points A, B and C are automatically stored on MMC. When a disc storing
hot cue points is inserted, the [A], [B] and [C] indicators light in green. To call
stored hot cue points, press the A, B or C button.
The green flashing indicator will light steadily (when the call is made, sound will
be interrupted briefly). If call is not needed, press the HOT CUE REC MODE
button. The indicator will change to red, and you can set the hot cue point. To call
the hot cue point, remove and replace the disc or MMC and the A, B and C buttons
will blink on and off, at this time it is possible to call.
WAVE display
When a wave display for one track is completed it is automatically stored on the
MMC. When the same track is played again, the stored WAVE display is automati-
cally called. Data for items beyond track number 21 are stored on the MMC.
CUE/LOOP
CALL
CUE/LOOP
DELETE
CUE/LOOP
MEMORY
2, 3
Copying MMC Data (From One MMC to Another)
Use the following procedure to copy data on one MMC (CARD A) to another MMC
(CARD B).
1. Remove the disc.
2. Remove the card.
3. Hold down the CUE/LOOP MEMORY button for 5 seconds
or longer.
[MMC>MMC(OVERWRITE), CARD A IN] is displayed.
4. Insert the MMC to copy data from in the card insertion slot.
[READING] is displayed.
5. After a few minutes, [CARD B IN] is displayed. Remove
card A and insert the destination card (CARD B) in the
insertion slot.
[WRITING] is displayed.
6. After a few minutes [CARD A IN] is displayed.
7. Repeat steps 4 to 6 twice for a 8M card and four times
for a 16M card to complete the copy operation.
[COMPLETE] is displayed when copying is completed.
It is impossible to copy from a card with greater capacity to the receiving card.
Copying Data in the Internal Memory
(Copying from internal memory onto MMC)
This procedure copies data in internal memory to MMC.
1. Remove the disc.
2. Remove the card.
3. Hold down the CUE/LOOP MEMORY button for 5 seconds
or longer.
[MMC>MMC(OVERWRITE), CARD A IN] is displayed.
4. Press the CUE/LOOP MEMORY button again.
[INT>MMC(OVERWRITE), CARD IN] is displayed.
5. Insert the destination MMC.
[WRITING] is displayed.
[COMPLETE] is displayed when copying is completed.
* If the [Err] message appears in one of the displays, the memory
data has not been copied properly. Turn the power to both
players OFF and then ON again, and repeat the copying proce-
dure from step 1.
* When copying from MMC to MMC, or from internal memory to
MMC, the MMC memory is overwritten; as a result, any data
previously recorded in MMC will be completely erased.
* Perform this procedure with the DIGITAL OUT mode set to "DJ".
Copie des données MMC (Dune carte MMC sur
une autre)
Effectuez les démarches suivantes pour copier une carte MMC (Carte A) sur une
autre (Carte B).
1. Retirez le disque.
2. Retirez la carte.
3. Tenez le bouton CUE/LOOP MEMORY enfoncé pendant 5
secondes ou plus.
Le message [MMC>MMC(OVERWRITE), CARD A IN] apparaît.
4. Dans la fente de lappareil, insérez la carte MMC doù
les données doivent être copiées (carte de source).
Le message [READING] apparaît.
5. Après quelques minutes, le message [CARD B IN]
apparaît. Retirez la carte A et insérez la carte de
destination (carte B) dans la fente de lappareil.
Le message [WRITING] apparaît.
6. Après quelques minutes, le message [CARD A IN]
apparaît.
7. Répétez les étapes 4 à 6 deux fois pour une carte 8 Mo
et quatre fois pour une carte 16 Mo de façon à terminer
la copie des données.
Le message [COMPLETE] apparaît quand la copie est terminée.
Il est impossible de copier dune carte ayant une plus grande capacité vers
la carte réceptrice.
Copie des données dans la mémoire interne
(Copie de la mémoire interne vers la carte MMC)
Ces démarches vont copier les données de la mémoire interne vers une carte MMC.
1. Retirez le disque.
2. Retirez la carte.
3. Tenez le bouton CUE/LOOP MEMORY enfoncé pendant 5
secondes ou plus.
Le message [MMC>MMC(OVERWRITE), CARD A IN] apparaît.
4. Appuyez à nouveau sur le bouton CUE/LOOP MEMORY.
Le message [INT>MMC(OVERWRITE), CARD IN] apparaît.
5. Insérez la carte MMC de destination.
Le message [WRITING] apparaît.
Le message [COMPLETE] apparaît quand la copie est terminée.
* Si le message [Err] apparaît sur un des deux affichages, c’est
que les données de la mémoire n’ont pas été correctement
copiées. Mettez les deux lecteurs hors tension (OFF), puis sous
tension (ON) et recommencez les démarches de la copie depuis
l’étape 1.
* Lors de la copie d'une carte MMC vers une autre MMC, ou de
la mémoire interne vers une carte MMC, le contenu de la carte
MMC est écrasé; par conséquent, toute donnée enregistrée
auparavant sur la MMC sera complètement effacée.
* Effectuez cette démarche après avoir réglé le mode DIGITAL
OUT sur "DJ".
USING CUE POINTS/LOOP POINTS MEMORY
ADVANCED OPERATIONS/DÉMARCHES ÉVOLUÉES
UTILISATION DE LA MÉMOIRE DE POINTS DE
REPÉRAGE / POINTS DE BOUCLE
7 Données autres que les points CUE/LOOP sur une carte
MMC
Points de repérage instantané A, B, C (HOT CUE) sur MMC
Les points de repérage instantané A, B et C sont automatiquement mémorisés
sur la carte MMC. Quand un disque comportant des points de repérage
instantané est inséré, les voyants [A], [B] et [C] sallument en vert. Pour
rappeler ces points, appuyez sur le bouton A, B ou C.
Le voyant vert clignotant sallume de façon continue (quand un rappel est
effectué, le son est brièvement interrompu). Si un rappel nest pas nécessaire,
appuyez sur le bouton HOT CUE REC MODE. Le voyant devient rouge et
vous pouvez régler le point de repérage instantané.
Pour rappeler les points de repérage instantané sur la MMC, retirez et réinsérez
le disque ou la MMC: les boutons A, B et C clignoteront. A ce stade, un rappel
est possible.
Affichage WAVE
Quand un affichage Wave est terminé pour une plage, il est automatiquement
mémorisé sur la MMC. Lorsque la même plage est lue à nouveau, laffichage
WAVE mémorisé est automatiquement rappelé. Les données pour les postes au-
delà du No. 21 sont mémorisées sur la MMC.