Filter
Top Products
48
Enjoying music in the remote zone
Controlling the TX-DS787 from the remote zone
1. Aiming at the remote sensor, press the ON
button on the remote controller.
Note:
Be aware that if you start using the system in the remote zone
(Zone 2) while a recording is going on in the main zone, the
recording will be stopped in the main zone.
2. Press the appropriate input selector button on
the remote controller to select the desired
source.
3. Adjust the volume to the desired level.
Notes:
• If the source for the main zone is selected as the source for the
remote zone and the source for the main zone is changed, then
the source for the remote zone will change as well.
• In the remote zone, you can only play the source in the 2-
channel mode. You cannot play the source in the remote zone
in the surround mode.
• You can only play the source in the Stereo mode or Direct
mode in the main zone, when you are playing the source in the
remote zone.
• If the Rec Out button is pressed in the main room while
someone is using the system in the remote zone, the Zone 2
function will be deactivated and the source will turn off in the
remote zone.
• The Zone 2 terminal is an analog output. Digital signals are not
output. If no sound is heard from the selected input source,
check if the component is connected to the analog inputs.
• Please note that some third-party multi-room system
components may not be fully compatible with the Onkyo
multi-room system components.
To select the same source for the remote zone that is selected
for the main zone, press the Zone 2 button again until
“Zone2Sel:SOURCE” appears in the display.
Adjusting the volume for the remote zone at the
TX-DS787
Following the procedure given below, you can adjust the volume
for the remote zone at the TX-DS787 without using the remote
controller.
1. Press the ZONE 2 VOL button.
2. While “ZONE 2Volume” is displayed, turn the
SSC dial to adjust the volume to the desired
level.
Controlling the TX-DS787 without the remote
controller
1. Press the Zone 2 button on the TX-DS787.
Ex.: When the CD button is pressed.
When “Zone2Sel:Off” is displayed, the output to the remote
zone is turned off.
TUNING
UPDOWN
FM
MUTE
/
MODE
DISPLAY STEREO
CHARACTER
/
MEMORY
DIRECT THX
SURROUND
BASS
/
TREBLE
EXIT
MENU
LISTENING
MODE
ZONE 2 VOL
CH LEVEL
FM
AM PHONO C
D
TAPEDVD
VIDEO
3
VIDEO
4
VIDEO
2
VCR
2
VIDEO
1
VCR
1
STANDBY/
ON
POWER
ANDBY
ST
ZONE
2
OFF
ON
REC OUT ZONE
2
PHONES
AV
RECEIVER
TX-DS
787
MASTER VOLUME
VIDEO AUDIOLR
VIDEO CAM INPUT/4
VIDEO
S VIDEO
AUDIO SELECTOR
PUSH TO ENTER
SMART SCAN
CONTROLLER
DSP/
PRESET
OPEN/CLOSEREC
AUDIO MUTING
DISCTRACK
DVD
CD
PH
TUN
T2T1
V1
STEREO
123
654
7
+
10 0
ENT
89
SURROUND T HX DSP
LEVEL
+
CH SELRe-EQ
LEVEL
–
DIMMER
HOME THEATER CONTROLLER
RC-390M
LATE NIGHT
DIRECT DSP
V2 V3 V
–
ON
VOL
ZONE 2
ZONE 2 VOL
SSC
/
DTS
PTY/
TP
Input source buttons
ZONE 2 indicator
INPUT
SELECTOR
buttons
Caution:
If you are not using the system in the remote Zone, always
press the ZONE 2 button consecutively to turn the ZONE 2
function off.
2. Select a source.
After pressing the Zone 2 button, you must press an input
source button within 3 seconds. The Zone 2 indicator lights.