Filter
Top Products
Page 39
Turntable
After pressing PHONO (with the remote control mode selector set to the “AUDIO/TV/VCR” position), you
can perform the following operations on a turntable:
PLAY: Starts playing.
STOP: Stops playing.
Cassette deck
After pressing TAPE or TAPE CONTROL (with the remote control mode selector set to the “AUDIO/TV/
VCR” position), you can perform the following operations on a cassette deck:
PLAY: Starts playing.
REW: First rewinds the tape from right to left.
FF: First rewinds the tape from left to right.
STOP: Stops operations.
PAUSE: Pauses playing or recording temporarily. To release it, press the PLAY button.
REC
¶¶
¶¶
¶: Press this button with the PLAY button to start recording.
Press this button with the PAUSE button to enter recording pause (standby).
Note:
You can use either the TAPE button or the TAPE CONTROL button to activate the buttons listed above. If you
press TAPE, the playing source also changes to “TAPE.” On the other hand, if you press TAPE CONTROL,
the playing source does not change to “TAPE.”
IMPORTANT:
To operate JVC’s video components using this remote control:
• You need to connect JVC video components through the AV COMPU LINK jacks (see page 36)
in addition to the connections using cables with RCA pin plugs (see pages 9 and 36).
• When operating the VCR, aim the remote control directly at the remote sensor on the VCR.
• When operating the TV, aim the remote control directly at the remote sensor on the receiver.
VCR
After pressing VCR or VCR CONTROL (with the remote control mode selector set to the “AUDIO/TV/VCR”
position), you can perform the following operations on the VCR:
PLAY: Starts playing.
REW: Rewinds a tape.
FF: Fast winds a tape.
STOP: Stops operations.
PAUSE: Pauses playing or recording temporarily. To release it, press the PLAY button.
REC
¶¶
¶¶
¶: Press this button with the PLAY button to start recording.
Press this button with the PAUSE button to enter recording pause (standby).
CHANNEL +/–: Changes the channels on the VCR.
1 – 9, 0: Selects the channels on the VCR.
Notes:
• You can use either the VCR button or the VCR CONTROL button to activate the buttons listed above. If you
press VCR, the playing source also changes to “VCR.” On the other hand, if you press VCR CONTROL,
the playing source does not change to “VCR.”
• You can also turn the VCR on and off by pressing VCR POWER on the remote control.
TV
After pressing TV SOUND (with the remote control mode selector set to the “AUDIO/TV/VCR” position),
you can perform the following operations on a TV:
CHANNEL +/–: Changes the channels.
TV VOLUME +/–: Adjusts the volume.
1 – 9, 0, 100+: Selects the channels.
TV/VIDEO: Sets the input mode (either TV or VIDEO).
RETURN: Alternates between the previously selected channel and the current channel.
Note:
You can also turn the TV on and off by pressing TV/CATV/SAT POWER on the remote control.
O
N
S
C
R
E
E
N
C
O
N
T
R
O
L
RM-SR772U REMOTE CONTROL
/SAT POWER
CD
DISC
CD
TRACK
SOUND
CONTROL
VCR
POWER
AUDIO
POWER
SLEEP
VIDEO TAPEVCR
TV
SOUND
TEST REAR
SEA MODE SURR MODE
FM/AM PHONOCD
546
213
87
/P 9
0
+10
10
AUDIO/TV
/VCR
MENU
EXIT
MENU
TAPE VCR
CONTROL
VOLUME
CHANNEL
MUTE
FF / ¢
PLAY
STOP
REC
TV/VIDEO
TV VOLUME
PAUSE
4 /
REW
TV/CATV
CNTRDELAY
CATV
/SAT
FM MODE/MUTE
100+
RETURN
ONE TOUCH
OPERATION
RX-772VBK[J]_0052-001A.En.38-48 97.4.8, 3:28 PM39