Filter
Top Products
13
Basic Settings
FR SP (Front Speaker) : To register the front speaker size.
CTR SP (Center Speaker) : To register the center speaker size.
REAR SP (Rear Speaker) : To register the rear speaker size.
* “LRG (large)” is the initial setting for the front speakers, and
“SML (small)” is for the center and rear speakers.
If you have already changed the setting, another size will be
shown.
3
Press CONTROL 3 (or 2) to select the
appropriate speaker size.
• Each time you press the button, the speaker size changes as
follows:
LRG (Large) : Select this when the speaker size is relatively
large. (See “Notes” below.)
SML (Small) : Select this when the speaker size is relatively
small. (See “Notes” below.)
NO :Select this when you have not connected a
speaker. (Not selectable for the front speakers)
4
Repeat steps
2
and
3
to select the appropriate
size for the other speakers.
Notes:
• Use the following criteria as reference when adjusting:
– If the size of the cone speaker unit built in your speaker is greater
than 4
3
/
4
inches (12 cm ), select “LRG (large),” and if it is smaller
than 4
3
/
4
inches (12 cm ), select “SML (small).”
• If you have selected “NO” for the subwoofer, you can only select
“LRG (large)” for the front speaker size.
• If you have selected “SML (small)” for the front speaker size, you
cannot select “LRG (large)” for the center and rear speaker sizes.
TO BE CONTINUED TO THE NEXT PAGE
Delay Time — CTR DL, REAR DL
Adjust the delay time of the sounds from the center speaker and
from the rear speakers, comparing to that of the sounds from the
front speakers. If the distance to the center speaker and/or the rear
speakers from your listening point is almost the same as that to the
front speakers, select 0 msec.
• 1 msec increase (or decrease) in delay time corresponds to 1 foot
(30 cm) increase (or decrease) in distance.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press SETTING.
The CONTROL buttons now work for basic
settings.
2
Press CONTROL ∞ (or 5) repeatedly until
“CTR DL (Center Delay)” or “REAR DL (Rear
Delay” (with the current setting)
* appears on the
display.
CTR DL (Center Delay) : To adjust the center delay time
(from 0 msec to 5 msec).
REAR DL (Rear Delay) : To adjust the rear delay time
(from 0 msec to 15 msec).
* “0 mS (msec)” is the initial setting for the center delay time
and
“5 mS (msec)” for the rear delay time. If you have already
changed the setting, another setting will be shown.
7 feet
(2.1 m)
8 feet
(2.4 m)
9 feet
(2.7 m)
10 feet
(3.0 m)
Left front
speaker
Right front
speaker
Right rear
speaker
Left rear
speaker
Center speaker
Ex.: In this case, set the center delay to “1 mS” and the
rear delay to “2 mS.”
ANALOG
PRO LOGIC
SUBWFRLFE
VOL
DGTL AUTO
INPUT ATT
DSP
LCR
LS S RS
LPCM
DOLBY D
DTS
CONTROL
SETTING
Ex.: When registering the rear speaker size
ANALOG
PRO LOGIC
SUBWFRLFE
VOL
DGTL AUTO
INPUT ATT
DSP
LCR
LS S RS
LPCM
DOLBY D
DTS
CONTROL
EN08-16.RX-E100SL[J]_f 01.3.7, 2:49 PM13