Filter
Top Products
43
c will flash green to confirm each
button press as you enter commands.
NOTE: While entering commands for
Power On/Off of any device during a
macro sequence, press the
Mute Button
. DO NOT press the actual Power
button.
3. When all the steps have been
entered, press the
Sleep Button
j to enter the commands. The red
light under the
Input Selectors
ef will blink and then turn off.
Example: To program the Macro 1
button so that it turns on the AVR580,
TV and a cable box, follow these steps:
• Press the
Macro 1 Button and
Mute Button at the same time
and then release them.
• Note that the
Program/SPL
Indicator
c will flash amber.
• Press the
AVR Selector f.
• Press the
Mute Button to store
the AVR580’s Power On command.
• Press the
VID 3 Input Selector
Button
e to indicate the next
command is for “TV Power On.”
• Press the
Mute Button to store
the TV Power On Command.
• Press the
VID 2 Input Selector
Button
e to
indicate the next com-
mand is for “Cable Power On.”
• Press the Mute Button to store
the Cable Power On command.
• Press the
Sleep/Channel Up
Button
j to complete the process
and store the macro sequence.
After following these steps, each time
you press the
Macro 1 Button ,
the remote will send the Power
On/Off command.
Erasing Macro Commands
To remove the commands that have been
programmed into one of the Macro but-
tons, follow these steps:
1. Press the
Mute Button and the
Macro Button that contains the
commands you wish to erase.
2. The
Program/SPL Indicator c
will flash amber, and the LED under
the
AVR Selector f will turn red.
3. Within 10 seconds, press the
Surround Mode Selector/Channel
Down Button
k.
4. The red LED under the
AVR Selector
f will go out, and the Program/
SPL Indicator
c will turn green
and flash three times before it
goes out.
5. When the
Program/SPL Indicator
c goes out, the Macro has been
erased.
Figure 12
Programmed Device Functions
Once the AVR580’s remote has been pro-
grammed for the codes of other devices,
press the appropriate
Input Selector e
to change the remote from controlling the
AVR580 to controlling the additional prod-
uct. When you press any one of the selec-
tors, it will briefly flash in red to indicate
that you have changed the device being
controlled.
When operating a device other than the
AVR580, the controls may not correspond
exactly to the function printed on the
remote or button. Some commands, such
as the volume control, are the same as
they are with the AVR580. Other buttons
will change their function so that they
correspond to a secondary label on the
remote. For example, the Sleep and
Surround mode selector buttons also func-
tion as the Channel Up and Channel Down
buttons when operating most TV sets,
VCRs or cable boxes. The Channel Up/
Down indication is printed directly on the
remote. For many standard CD players,
cassette decks, VCRs and DVD functions,
the standard function icons are printed on
top of the buttons.
For some products, however, the function
of a particular button does not follow the
command printed on the remote. In order
to see which function a button controls,
consult the Function List tables on pages
46 and 47. To use those tables, first
check the type of device being controlled
(e.g., TV, VCR). Next, look at the remote
control diagram in Figure 12. Note that
each button has a number on it.
T
o find out what function a particular but-
ton has for a specific device, find the but-
ton number on the
Function List and then
look in the column for the device you are
controlling. For example, button number
45
is the Direct button for the AVR580,
but it is the “Favorite” button for many
cable television boxes and satellite
receivers. Button number 31 is the
Delay button for the AVR580, but the
Open/Close button for CD players.
NOTE: The numbers used to describe
the button functions in Figure 12 for the
purposes of describing how a button
operates are a different set of numbers
than those used in the rest of this manual
to describe the button functions for the
AVR580.
31
43
31
43
43
43
43
31
43