Filter
Top Products
48
Enjoying music in the remote zone
Controlling the DTR-7.1 from the remote zone
1. Aiming at the remote sensor, press the ON
button on the remote controller.
Note:
Be aware that if you start using the system in the remote zone
(Zone 2) while a recording is going on in the main zone, the
recording will be stopped in the main zone.
2. Press the appropriate input selector button on
the remote controller to select the desired
source.
3. Adjust the volume to the desired level.
• When the speakers are connected to the ZONE 2 SPEAKERS
terminals:
Adjust the volume using the VOL buttons on the remote
controller.
• When an amplifier is connected to the ZONE 2 OUT
terminals:
Adjust the volume at the amplifier in the remote zone (Zone 2).
Caution:
If you are not using the system in the remote Zone, always
press the Zone 2 button consecutively to turn the ZONE 2
function off.
Notes:
• If the source for the main zone is selected as the source for the
remote zone and the source for the main zone is changed, then
the source for the remote zone will change as well.
• The analog signals of the L and R channels for the selected
source are output to Zone 2.
• You can only play the source in the Stereo mode or Direct
mode in the main zone, when you are playing the source in the
remote zone.
(When speakers are connected to the ZONE 2 SPEAKERS
terminals.)
• If the Rec Out button is pressed in the main room while
someone is using the system in the remote zone, the Zone 2
function will be deactivated and the source will turn off in the
remote zone.
• The Zone 2 terminal is an analog output. Digital signals are not
output. If no sound is heard from the selected input source,
To select the same source for the remote zone that is selected
for the main zone, press the Zone 2 button again until
“Zone2Sel:SOURCE” appears in the display.
Controlling the DTR-7.1 without the remote
controller
1. Press the Zone 2 button on the DTR-7.1.
2. Select a source.
After pressing the Zone 2 button, you must press an input
source button within 3 seconds. The Zone 2 indicator lights.
Ex.: When the CD button is pressed.
When “Zone2Sel:Off” is displayed, the output to the remote
zone is turned off.
When speakers are connected to the ZONE 2 SPEAKERS
terminals, you can adjust the volume using the controls at the
DTR-7.1.
1. Press the Zone 2 Vol button.
2. While “ZONE 2Volume” is displayed, turn
the SSC dial to adjust the volume to the
desired level.
When an amplifier is connected to the ZONE 2 OUT terminals,
you cannot adjust the volume at the DTR-7.1. Adjust the
volume at the amplifier in the remote zone (Zone 2).
OPEN/COLSEREC
AUDIO MUTING
DISCTRACK
DVD
CD
PH
TUN
T2T1
V1
STEREO
123
654
7
+
10 0
ENT
89
SURROUND T HX DSP
LEVEL
+
CH SELRe-EQ
LEVEL
–
DIMMERLATE NIGHT
DIRECT DSP
V2 V3 V
–
ON
VOL
Smart Scan
Controller
Push To Enter
DSP/Preset
Standby/On
Standby
Zone 2
Rec Out
Zone 2
Phones
Master Volume
Video 1
VCR 1
Video 2 Video 3 Tape
FM
AM Phono CDDVD
Dimmer
Down UpTuning
Stereo
Display
Listening Mode
/DTS
Surround
On
O
f
f
Power
FM Mute/
Mode
Character/
Memory
Bass/
Treble
Zone 2 VolCH Level
ExitDirect THX Menu
Video 4
/
Video Cam Input
S Video Video
L Audio
R
--
VCR 2
Video 4
Audio
Selector
HOME THEATER CONTROLLER
RC-418M
Zone 2
Zone 2 Vol
SSC
Input source buttons
Zone 2 indicator
INPUT
SELECTOR
buttons