Filter
Top Products
30
Speaker Setup
1. Speaker Setup menu
After you have installed the DTR-7.1, connected all the
components, and determined the speaker layout, it is now time to
perform the settings in the Speaker Setup menu for the optimum
sound acoustics for your environment and speaker layout.
Before you perform the following settings, it is important that you
first determine the following characteristics:
• The types and sizes of the speakers that are connected.
• The distance from each speaker to your normal listening
position.
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.OSD Setup
|ENTER| Quit:|OSD|
1.Speaker Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Bass Peak Level
|ENTER| Quit:|OSD|
1-1.Speaker Config
a.Subwoofer :Yes
b.Front :Small
c.Center :Small
d.Surr L/R :Small
e.Surr Back :Small
f.Surr Back Out :1ch
Quit:|OSD|
1-1. Speaker Config sub-menu
Here you will enter which speakers are connected and the size of
each speaker.
a. Subwoofer
Yes: Select when a subwoofer is connected.
No: Select when a subwoofer is not connected.
b. Front
Large: Select if the front speakers are large sized.
Small: Select if the front speakers are small sized.
• If “No” is selected for the Subwoofer setting, then this setting
is fixed to “Large.”
c. Center
None: Select if no center speaker is connected.
Large: Select if the center speaker is large sized.
Small: Select if the center speaker is small sized.
• If “Small” is selected for the Front setting, then “Large”
cannot be selected for this setting.
d. Surr L/R
None: Select if no surround left and right speakers are connected.
Large: Select if the surround left and right speakers are large
sized.
Small: Select if the surround left and right speakers are small
sized.
• If “Small” is selected for the Front setting, then “Large”
cannot be selected for this setting.
e. Surr Back
None: Select if no surround back left and right speakers are
connected.
Large: Select if the surround back left and right speakers are large
sized.
Small: Select if the surround back left and right speakers are small
sized.
• If “None” is selected for the Surround L/R setting, then this
setting is fixed to “None.” (The display also disappears from
the screen.)
• If “Small” is selected for the Surround L/R setting, then
“Large” cannot be selected for this setting.
f. Surr Back Out
1ch: Select if there is only one surround back speaker.
2ch (Preout Only): Select if there are two surround back
speakers. (For preout output only.)
Memo:
(Only one surround back speaker)
Tip:
When setting the speaker size in the Speaker Config sub-menu,
use the guidelines given below.
Large: The complete frequency range for the channel you are
setting will be output from the speaker.
Small: Frequencies of the channel you are setting lower than 80
Hz will be output from the subwoofer. If the front speakers are
set to “Large,” then the sound may be output from both the left
and right speakers. (Set all speakers for THX speaker systems
to “small.”)
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.OSD Setup
|ENTER| Quit:|OSD|
1.Speaker Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Bass Peak Level
|ENTER| Quit:|OSD|
(Two surround back speakers)
SL SR
SBL SBR
Front
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
Front
SW Center
Monitor
SL SR
SB
Front
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
Front
SW Center
Monitor