Filter
Top Products
49
ADVANCED FUNCTIONS
background, Medium for partial transparency or Opaque to block video
programs while the menus are on screen.
Volume Status Messages: When the AVR is turned on, the volume
is adjusted or the source is changed, or if a change in the input signal
is detected, a status message will be displayed on screen. Select how
long the message remains visible, from 2 to 10 seconds, with a default
of 3 seconds.
Menus: The settings in the Surround Modes, Video Modes and Audio
Effects menus only remain in effect during the current listening session.
This setting governs how long these menus remain visible after the last
adjustment, varying from 2 to 10 seconds, with a default of 3 seconds.
Setup and Slide-In Menus: This setting determines how long the
setup menus (Main Menu, Speaker Setup Menu, Zone 2 Menu, all
slide-in menus) remain visible after the last adjustment. Select a timeout
period of 5, 10 or 15 (the default) minutes, or no timeout, which leaves
the menus on screen until manually cleared. A timeout period avoids
the possibility of burn-in damage to plasma or CRT displays.
Screen Saver: Program a timeout period for no activity (with no
menus displayed) before the AVR’s built-in screen saver begins. Select
a period of 5 (the default), 10 or 20 minutes, or turn off the screen
saver. A timeout period avoids the possibility of burn-in damage to
plasma or CRT displays.
Advanced Remote Control Functions
The AVR 3550HD remote control also serves as a universal remote
that may be programmed to operate other components. Refer to the
Function List (Table A13 in the appendix) for assistance in operating
your other components.The function of each button will not necessarily
correspond to the label printed on the button.
Punch-Through Programming
The punch-through feature allows you to operate one component, while
setting certain groups of controls to operate another component. For
example, while using the AVR controls for surround modes and other
audio functions, you may operate the transport controls of your DVD
player. Or while using the remote to control video functions on your TV,
you may use your cable box to change channels.
To program punch-through control while operating any device:
1. Press and hold the Source Selector (or AVR Settings Button) for the
main device the remote will be operating. The Source Selector will
light, go dark and then light up again, indicating the remote is in
Program mode and that you may release the button.
2. Select the type of punch-through programming.
a) For channel control punch-through, press the Channel Up Button.
b) To program transport control punch-through, press the Play Button.
3. Press the Source Selector for the device whose channel or transport
controls will be used while operating the device selected in the first
step.The Source Selector will flash to confirm.
For example, to watch the TV while changing channels using the cable
box, press and hold the TV Button until it lights. Then press the Channel
Up Button, followed by the CBL/SAT Button.
To undo punch-through programming, follow the same steps as above,
but press the same Source Selector in Steps 1 and 3.
NOTE: The Volume and Mute controls are always dedicated to
the AVR.
Activities (Macros)
Activities are used to program sequences of up to 19 commands that
are executed with a single button press.Activities are well suited for
power on and off commands, to send out a multidigit channel number
with one button press, or to control another device with more flexibility
than the built-in punch-through controls. Up to eleven activities may be
programmed.
NOTE: Use caution when programming complicated activities.
It isn’t possible to program a pause or delay before sending com-
mands after Power On, and the component may not be ready to
respond to commands immediately after powering on.
To program, or “record” an activity, follow these steps:
1. To enter Program mode, simultaneously press and hold the Activity
Button and the Alphanumeric Key or AVR Power On Button to which
the activity will be assigned.
2. Press the Source Selector (or AVR Settings Button) for each device
before you enter individual commands.This step counts as one of
the 19 commands allowed for each activity.
3. For Power On, press the AVR or Device Power On Button.
4. Press the AVR or Device Power Off Button for Power Off.
5. Press the Activity Button to end the programming process, and the
last Source Selector (or the AVR Settings Button) will flash three times.
It isn’t possible to “edit” a command within an activity. To erase the activity:
1. Press and hold the Activity Button and the Alphanumeric Key or
AVR Power On Button until the Source Selector or AVR Settings
Button lights.
2. Press the Activity Button to erase the activity.
To execute an activity, press the Activity Button, then press the Alphanumeric
Key (or the AVR Power On Button) for the Activity.
Learning
If you have programmed a product’s codes into the remote and find
that some functions are missing, the AVR 3550HD remote may “learn”
individual codes from the product’s original remote. See page 28.
Resetting the Remote
To reset the remote to its factory defaults, simultaneously press and
hold the TV Source Selector and the “0” Alphanumeric Key. When the