Filter
Top Products
37
OPERATION
use is also compatible, but has been discontinued. Other modules that
have standard analog or digital audio outputs, may be connected to a
compatible input and operated using their own controls.
NOTE: To listen to XM Radio using the AVR 3550HD, you will
need to purchase an XM antenna module and subscription, and
activate your module. XM service is not available in Alaska or
Hawaii. Visit the XM Radio Web site at www.xmradio.com for
more information.
Plug the module into the XM Antenna Jack on the rear of the AVR 3550HD.
Place the antenna module so that it has a clear view through a south-
facing window.
Select XM Radio as the source in one of these ways:
1. Press the Source List Button on the front panel. Press it again
repeatedly until XM Radio is selected, or use the
⁄
/
¤
Buttons
to scroll.
2. Press the Radio Source Selector on the remote repeatedly until
XM Radio is selected.
There are four ways to tune an XM Radio channel:
1. Use the
⁄
/
¤
Buttons or the Channel Control to scan through the
channel numbers.
2. Use the
‹
/
›
Buttons to scan through any previously programmed
preset stations.
3. After you have programmed presets, directly enter the preset number
(1 through 40) using the Alphanumeric Keys. For single-digit positions,
enter a “0” before the number.
4. Press the Menu Button to search for a channel by: preset, category,
all channels or direct entry.
When you are able to hear Channel 1, you are ready to activate your
module. If you don’t hear Channel 1, make sure the module’s plug is
firmly seated in the XM Antenna jack, and that the module is near a
south-facing window.Try unfolding the module and rotating it to obtain
reception. You may need to purchase an extension cable to ensure that
the module is near the window.
Tune to Channel 0 for a display of your module’s Radio ID number.
The current channel number and preset location will appear in the upper
line of the Message Display, and the channel name will appear in the
lower line.Three signal-strength bars will appear to the right of the channel
number and preset location. The song title, artist and channel category,
along with the channel number and preset position (if programmed), will
all appear on screen when a video display is in use.
For traffic and weather channels, the current city’s name will appear
instead of the channel name, and the local weather and temperature
will be displayed on screen.
To store a channel in one of the 40 preset locations:
1. Tune to the desired channel and press the OK Button. The lowest
available preset number will flash.
2. Use the Alphanumeric Keys to enter the numbered preset location
you wish to store the channel in, or do nothing if the current preset
location is acceptable.
3. Press the OK Button to store the new preset.
Recording
Two-channel analog and digital audio signals, as well as composite
and S-video signals, are normally available at the appropriate recording
outputs.To make a recording, connect your audio or video recorder to
the appropriate output jacks, as described in the Installation section,
insert blank media and make sure the recorder is turned on and record-
ing while the source is playing.
NOTES:
1. Analog and digital audio signals are not converted to the
other format. Both coaxial and optical digital audio are avail-
able at the Coaxial Digital Audio Output.
2. Only PCM digital audio signals are available for recording.
Proprietary formats such as Dolby Digital and DTS may not
be recorded using the digital audio connections. Use the
analog audio connections to make an analog recording.
3. HDMI and component video sources are not available for
recording.
4. Please make certain that you are aware of any copyright
restrictions on any material you record. Unauthorized duplica-
tion of copyrighted materials is prohibited by federal law.
Using Docking Station
The Bridge II is an included dock that is compatible with most docking
iPod models, 4G and later (not included). When The Bridge II is con-
nected to its proprietary input on the AVR 3550HD and the iPod is
docked, you may play the audio, video and still-image materials on your
iPod through your high-quality audio/video system, operate the iPod
using the AVR remote or the AVR’s front-panel controls, view navigation
messages on the AVR’s front panel or a connected video display,
and charge the iPod.
When the source The Bridge is selected and an iPod is docked, the
message “The Bridge is CONNECTED” appears the front panel. If the
AVR doesn’t detect the iPod, turn off the AVR, remove the iPod from
The Bridge II and reset the iPod. When the iPod returns to its main
menu, redock it and turn on the AVR.
When The Bridge II is connected, the screen shown in Figure 62
will appear.