Filter
Top Products
MAIN REMOTE CONTROL FUNCTIONS
MAIN REMOTE CONTROL FUNCTIONS 11MAIN REMOTE CONTROL FUNCTIONS 11
IMPORTANT NOTE: The AVR 330’s remote may be
programmed to control up to eight devices, including
the AVR 330. Before using the remote, it is important to
remember to press the Input Selector Button e
that corresponds to the unit you wish to operate.
In addition, the AVR 330’s remote is shipped from
the factory to operate the AVR 330 and most
Harman Kardon CD or DVD players and cassette
decks. The remote is also capable of operating a
wide variety of other products using the control codes
that are part of the remote. Before using the remote
with other products, follow the instructions on pages
35–36 to program the proper codes for the products
in your system.
It is also important to remember that many of the but-
tons on the remote take on different functions, depend-
ing on the product selected using the Device Control
Selectors. The descriptions shown here primarily detail
the functions of the remote when it is used to operate
the AVR 330. (See page 36 for information about
alternate functions for the remote’s buttons.)
a Power Off Button: Press this button to place the
AVR 330 or a selected device in the Standby mode.
Note that this will turn off the main room functions, but if
the Multiroom system is activated, it will continue to
function.
b IR Transmitter Window: Point this window
towards the AVR 330 when pressing buttons on the
remote to make certain that infrared commands are
properly received.
c Program/SPL Indicator: This three-color indica-
tor is used to guide you through the process of pro-
gramming the remote, and it is also used as a level
indicator when using the remote’s EzSet capabilities.
(See page 23 for more information on setting output
levels, and see page 35 for information on program-
ming the remote.)
d Power On Button: Press this button to turn on
the power to a device selected by pressing one of the
Input Selectors e.
e Input Selectors: Pressing one of these buttons
will perform three actions at the same time. First, if the
AVR 330 is not turned on, this will power up the unit.
Next, it will select the source shown on the button as
the input to the AVR 330. Finally, it will change the
remote control so that it controls the device selected.
After pressing one of these buttons you must press
the
AVR Selector Button f again to operate the
AVR 330’s functions with the remote.
f AVR Selector: Pressing this button will switch the
remote so that it will operate the AVR 330’s functions. If
the AVR 330 is in the Standby mode, it will also turn the
AVR 330 on.
g AM/FM Tuner Select: Press this button to select
the AVR 330’s tuner as the listening choice. Pressing
this button when the tuner is already in use will select
between the AM and FM bands.
h Dim Button: Press this button to activate the
Dimmer function, which reduces the brightness of the
front panel display, or turns it off entirely. The first press
of the button shows the default state, which is full bright-
ness by indicating
DIMMER FULL in the Lower
Display Line
¯. Press the button again within five
seconds to reduce the brightness by 50%, as indicated
by
DIMMER HALF showing in the Lower
Display Line
¯. Press the button again within five
seconds and the main display will go completely dark.
Note that this setting is temporary, in that regardless of
any changes, the display will always return to full bright-
ness when the AVR is turned on. In addition, the
Power
Indicator
2 will always remain at full brightness
regardless of the setting. This is to remind you that the
AVR is still turned on.
i Test Button: Press this button to begin the
sequence used to calibrate the AVR 330’s output levels.
(See page 23 for more information on calibrating the
AVR 330.)
j Sleep Button: Press this button to place the unit
in the Sleep mode. After the time shown in the display,
the AVR 330 will automatically go into the Standby
mode. Each press of the button changes the time until
turn-off in the following order:
This button is also used to change channels on your
TV when the TV is selected.
When the AVR 330 remote is being programmed with
the codes to operate another device, this button is also
used in the “Auto Search” process. (See page 35 for
more information on programming the remote.)
k DSP Surround Mode Selector: Press this but-
ton to cycle through the DSP, VMAx and Stereo sur-
round modes such as Hall, Theater, VMAx Near and
Far, and Surround Off. This button is also used to tune
channels when the TV is selected using the device
Input Selector e.When the AVR 330 remote is
being programmed with the codes of another device,
this button is also used in the “Auto Search” process.
(See page 35 for more information on programming
the remote.)
l Night Mode: Press this button to activate the
Night mode. This mode is available in specially
encoded digital sources, and it preserves dialogue
(center channel) intelligibility at low volume levels.
m Channel Select Button: This button is used to
start the process of setting the AVR 330’s output levels to
an external source. Once this button is pressed, use the
⁄
/
¤
Buttons n
to select the channel being adjusted,
then press the Set Button p, followed by the
⁄
/
¤
Buttons
n again, to change the level setting. (See
page 30 for more information.)
n
⁄
/
¤
Buttons: These multipurpose buttons are
used to change or scroll through items in the on-
screen menus, make configuration settings such as
digital inputs or delay timing, or to select surround
modes. When changing a setting, first press the button
for the function or setting to be changed (e.g., press
the
DSP Surround Mode Selector k to select a
sound field mode or the
Digital Select Button q
to change a digital input) and then press one of these
buttons to scroll through the list of options or to
increase or decrease a setting. The sections in this
manual describing the individual features and functions
contain specific information on using these buttons for
each application.
o
‹/›
Buttons: These buttons are used to change
the menu selection or setting during some of the setup
procedures for the AVR 330.
p Set Button: This button is used to enter settings
into the AVR 330’s memory. It is also used in the
setup procedures for delay time, speaker configuration
and channel output level adjustment.
q Digital Select: Press this button to assign one
of the digital inputs
*(wz to a source. (See
page 26 for more information on using digital inputs.)
r Numeric Keys: These buttons serve as a 10-
button numeric keypad to enter tuner preset positions.
They are also used to select channel numbers when
TV, Cable or SAT has been selected on the remote, or
to select track numbers on a CD, DVD or LD player,
depending on how the remote has been programmed.
s Tuner Mode: Press this button when the tuner
is in use to select between automatic tuning and
manual tuning. When the button is pressed so that
MANUAL appears in the Lower Display Line ¯,
pressing the
Tuning Buttons u9
≠
will move
the frequency up or down in single-step increments.
When the FM band is in use, pressing this button
when a station’s signal is weak will change to monau-
ral reception. (See page 29 for more information.)
90
min
80
min
70
min
60
min
50
min
40
min
30
min
20
min
10
min
OFF
MAIN REMOTE CONTROL FUNCTIONS