Filter
Top Products
OPERATION
26 OPERATION
• For private listening, plug the 1/4" stereo phone
plug from a pair of stereo headphones into the
front-panel
Headphone Jack
4
.When the
headphone plug is connected, the word
HEADPHONE will scroll once across the
Lower Display Line ¯ and all speakers will be
silenced. When the headphone plug is removed, the
audio feed to the speakers will be restored.
Surround Mode Selection
One of the most important features of the AVR 330
is its ability to reproduce a full multichannel surround
sound field from digital sources, analog matrix
surround-encoded programs and standard
stereo programs.
Selection of a surround mode is based on personal
taste, as well as the type of program source material
being used. For example, motion pictures or TV
programs bearing the logo of one of the major
surround-encoding processes, such as Dolby Surround
or DTS Stereo, may be played in either the Dolby
Digital, Dolby Pro Logic II Cinema, DTS Neo:6 Cinema
or Logic 7 Cinema surround modes, depending on the
source material.
NOTE: Once a program has been encoded with matrix
surround information, it retains the surround information
as long as the program is broadcast in stereo. Thus,
movies with surround sound may be decoded via any
of the analog surround modes such as Pro Logic II
Movie, Logic 7 Cinema or DTS Neo:6 Cinema, when
they are broadcast via conventional TV stations, cable,
pay-TV and satellite transmission. In addition, a growing
number of made-for-television programs, sports broad-
casts, radio dramas and music CDs are also recorded in
surround sound. You may view a list of these programs
at the Dolby Laboratories Web site at www.dolby.com.
Even when a program is not listed as carrying intentional
surround information, you may find that the Pro Logic II,
Logic 7 Enhanced or DTS Neo:6, VMAx and the Hall or
Theater modes often deliver enveloping surround pre-
sentations through the use of the natural information
present in all stereo recordings.
Surround modes may be changed at any time by
using either the front panel or remote control. To
select a new surround mode from the front panel, first
press the
Surround Mode Group Selector Button
7 until the desired major surround mode group such
as Dolby, DTS or Logic 7 is selected. Next, press the
Surround Mode Selector Button 8 to choose the
specific individual surround mode.
To select a surround mode using the remote, press
the button for the major surround mode group that
includes the mode you wish to choose from:
Dolby
w, DTS Surround x, DTS Neo:6 ,
Logic 7 y, Stereo or DSP Surround k.
The first press of the button will show the current mode
from that group if it is already in use, or the first avail-
able mode if you are currently using another mode. To
cycle through the available modes in that group, press
the button again until the desired mode appears in the
Lower Display Line ¯, in the on-screen display and
in the
Surround Mode Indicators ˘.
As the surround modes change, the appropriate
Surround Mode Indicator ˘ will light to indicate
which mode has been selected.
The Dolby Digital, Dolby Digital EX and DTS 5.1,
DTS-ES Matrix and DTS-ES Discrete modes may only
be selected when a digital input is in use. In addition,
when a digital source is present, the AVR 330 will
automatically select and switch to the correct mode,
regardless of the mode that has been previously
selected. For more information on selecting digital
sources, see the Digital Audio Playback section below.
When the 6-channel/8-channel direct inputs are in
use there is no surround processing, as these inputs
take the analog output signals from an optional, exter-
nal DVD-Audio or SACD player, or another source
device and carry them straight through to the volume
control without any further digital processing.
To listen to a program in traditional two-channel stereo,
using the front left and front right speakers only (plus
the subwoofer, if installed and configured), press the
Stereo Button until SURR OFF appears in the
Lower Display Line ¯, or press the Surround Mode
Group Selector
7 until the Stereo
modes appear in
the on-screen display and
Lower Display Line ¯.
Next, press the
Surround Mode Select Button 8
until SURROUND OFF appears in the on-screen
display and
Lower Display Line ¯.
Digital Audio Playback
Digital audio is a major advancement over older analog
surround processing systems such as Dolby Pro Logic.
It delivers five discrete channels: left front, center, right
front, left surround and right surround. Each channel
reproduces full frequency range (20Hz to 20kHz) and
offers dramatically improved dynamic range and signifi-
cant improvements to signal-to-noise ratios. In addition,
digital systems have the capability to deliver an additional
channel that is specifically devoted to low-frequency
information. This is the “.1” channel referred to when you
see these systems described as “5.1,” “6.1” or “7.1.”
The bass channel is separate from the other channels,
but since it is intentionally bandwidth-limited, sound
designers have given it that unique designation.
Dolby Digital
Dolby Digital is a standard part of DVD, and is avail-
able on specially encoded LD discs and satellite broad-
casts and it is a part of the high-definition television
(HDTV) system.
An optional, external RF demodulator is required to
use the AVR 330 to listen to the Dolby Digital sound-
tracks available on laser discs. Connect the RF output
of the LD player to the demodulator and then connect
the digital output of the demodulator to the
Optical or
Coaxial Inputs *(dg of the AVR 330. No
demodulator is required for use with DVD players or
DTS-encoded laser discs.
DTS
DTS is another digital audio system that is capable of
delivering 5.1 or 6.1 discrete or matrix sound field
reproduction. Although both DTS and Dolby Digital are
digital, they use different methods of encoding the sig-
nals, and thus they require different decoding circuits
to convert the digital signals back to analog.
DTS-encoded soundtracks are available on select DVD
and LD discs, as well as on special audio-only DTS
discs. You may use any LD or CD player equipped
with a digital output to play DTS-encoded discs with
the AVR 330. All that is required is to connect the
player’s output to either an
Optical or Coaxial Input
on the rear panel dg or front panel *(.
In order to listen to DVDs encoded with DTS sound-
tracks, the DVD player must be compatible with the
DTS signal as indicated by a DTS logo on the player’s
front panel. Early DVD players may not be able to play
DTS-encoded DVDs. This does not indicate a problem
with the AVR 330, as some players cannot pass the
DTS signal through to the digital outputs. If you are in
doubt as to the capability of your DVD player to handle
DTS discs, consult the player’s owner’s manual.
NOTE: Some DVD players have a default setting that
does not pass through the DTS signal. Before playing
DVDs with a DTS soundtrack, make certain that the
settings in your DVD player have been properly adjusted
so that DTS audio is passed through. Consult the
owner’s manual for your DVD player for more
information on making these settings.
Selecting a Digital Source
To utilize either digital mode, you must have properly
connected a digital source to the AVR 330. Connect
the digital outputs from DVD players, HDTV receivers,
satellite systems or CD players to the
Optical or
Coaxial Inputs *(dg. In order to provide a
backup signal and a source for analog stereo recording,
the analog outputs provided on digital source equipment
(Continued on p. 28)
28
28
29