Filter
Top Products
A5 Tone Control
Turn tone adjustments off.
[Selectable items]
ON
: Playback without tone adjustment.
OFF
: Allow tone adjustment (treble, bass).
The tone cannot be adjusted when in the DIRECT mode.
A6 Bass
Adjust low frequency range (bass).
[Variable range]
–6dB
~
0dB
~
+6dB
A7 Treble
Adjust high frequency range (treble).
[Variable range]
–6dB
~
0dB
~
+6 dB
“Bass” and “Treble” can be set when “Tone Defeat” is set to “OFF”.
A3 SUBWOOFER ATT.
Attenuate subwoofer level when using EXT. IN mode.
[Selectable items]
ON
: The input from the subwoofer channel is attenuated.
OFF
: The input from the subwoofer channel is not attenuated.
Usually use in this mode.
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
A4 Subwoofer
Turn subwoofer output on and off.
[Selectable items]
ON
: The subwoofer is used.
OFF
: The subwoofer is not used.
For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 33).
A2 SB CH OUT (for Multi-channel sources)
Select playback mode for surround back channels.
[Selectable items]
OFF
: No signal is played from the surround back
channels.
MTRX ON
: The surround channel signals undergo digital matrix
processing and are output from the surround back
channels.
PL
II
x C
z1
: Decoded in Dolby Pro Logic IIx Cinema mode,
surround back signal played.
PL
II
x M
z2
: Decoded in Dolby Pro Logic IIx Music mode,
surround back signal played.
ES MTRX
z3
: DTS signal played with digital matrix processing.
ES DSCRT
z4
: Signal included in DTS-ES Discrete 6.1-channel
sources played.
z1: This can be selected when “Surround Back Speaker” is set to
“2spkrs” at the “System Setup” – “Speaker Setup” setting
(vpage 23).
z2: This can be selected when “Surround Back Speaker” is set to
“2spkrs” or “1spkr” at the “System Setup” – “Speaker Setup”
setting.
z3: This can be selected when playing DTS sources.
z4: This can be selected when playing DTS sources including a
discrete 6.1-channel signal identification signal.
A2 SB CH OUT (for 2-channel sources)
Determine whether to use surround back speakers.
[Selectable items]
ON
: The surround back channel signal is played.
OFF
: The surround back channel signal is not played.
• If the settings of speakers for which “None” has been determined
at “Auto Setup” are changed, “Audyssey”, “Audyssey Byp. L/R” and
“Audyssey Flat” cannot be selected. Either perform Auto Setup
again, or return to the setting after running Auto Setup with “System
Setup” – “Speaker Setup” – “Restore”.
• When using headphones, “MultEQ” is set to “OFF”.
A8 MultEQ
Select the type of room correction desired from the following list:
[Selectable items]
Audyssey
: Optimize frequency response of all speakers.
Byp. L/R
: Optimize frequency response of speakers except front
L and R speakers.
Flat
: Optimize frequency response of all speakers to flat
response.
OFF
: Turn equalizer off.
NOTE
• “MultEQ” can only be set when Auto Setup has been performed.
• “MultEQ” cannot be set in the following situations.
・If “Auto Setup” fails to be completed.
・After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
Operating from the main unit or main remote
control unit
Press MULTEQ.
• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is
selected, the Audyssey MultEQ indicator lights green.
• After running Auto Setup, if the Speaker Configuration, Distance,
Channel Level and Crossover Frequency have changed without
increasing the number of speakers measured, the Audyssey MultEQ
indicator lights red.
OFF
Audyssey
Audyssey Byp. L/R
Audyssey Flat
Settings can also be made when [STD] is pressed.
When using surround back speakers, adopt the following
settings.
q Adopt “7.1CH” for the AMP Assign setting.
・The default setting for the Amp Assign mode of AVR-1709 is
“ZONE2”.
w Adopt a setting other than “OFF” for the “SB CH OUT” setting
of “Surround Parameter”.
NOTE
When the “Dynamic EQ” setting is “ON”, setting is not possible.
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
ENGLISH