Filter
Top Products
Setting the Remote ID
When using multiple DENON AV receivers in the same room,
make this setting so that only the desired AV receiver operates.
1
Press [AMP] to set the main remote control unit to the
AMP mode.
2
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice.
3
Refer to the table at the right, and use [NUMBER] to
input the 5-digit number corresponding to the remote
ID to be changed.
The signal transmission indicator flashes twice.
4
Press [TU], [iPod] or [NET/DTU] to select the mode to
be set.
5
Repeat steps 2 to 4 to set the remote IDs for all modes.
NOTE
• When changing a setting, be sure to set the same remote ID as the
AVP-A1HDCI’s (vpage 41).
• When changing the AMP mode’s remote ID, also change the
“TUNER”, “iPod” and “NET/DTU” remote ID at the same time.
• Set the remote ID of an analog tuner for “TUNER” ( ), the XM
remote ID for “ ”.
5
Point the main remote control units directly at each
other and press and hold the button on the other
device’s remote control unit that you want to learn.
Once learning is completed normally, the display lights and the
signal transmission indicator flashes twice.
b If you want to learn other buttons, repeat steps 4 and 5.
b The mode can be switched by pressing [MODE SELECTOR].
b The signal transmission indicator lights once for a long time if
learning was not possible
6
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice and the setting
is completed.
[NUMBER]
[MODE SELECTOR]
[RC SETUP]
[ NET/DTU]
[ TU]
[ AMP]
[ iPod]
Other device’s
remote control unit
AVP-A1HDCI’s main remote
control unit (RC-1067)
Learning Function
If your AV devices are of a brand other than DENON or if they
cannot be operated with the preset memory function, their remote
control signals can be transfered to stored in the AVP-A1HDCI’s
main remote control unit.
1
Press [MODE SELECTOR] for the device you want to
set.
2
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice.
3
Press [9], [7] and [5], in that order.
The signal transmission indicator flashes twice and the learning
mode is set.
4
Press the button to be set.
The main remote control unit’s display turns off.
b If a button that cannot be learned is pressed, the signal transmission
indicator lights but the signal is not learned.
• With some remote control units, the signals cannot be learned or the
device will not operate properly even when the signals have been
learned. In this case, use the device’s own remote control unit.
• Learned buttons have priority over the preset memory. If you no
longer need the learned setting, reset the learning function (vpage
78).
NOTE
• [HOME] cannot be learned.
• Do not learn any remote control signals at [RC SETUP].
• The AMP, ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes
cannot be learned.
Signal transmission
indicator
MODE
SELECTOR
Remote ID
AMP
(MAIN)
TUNER
iPod
NET/DTU
(Analog
TUNER)
(XM)
(Net
Audio)
(HD
Radio)
1
(Default)
81001 52863 52864 72815 62865 62840
2 82001 52795 52812 72816 62837 62841
3 83001 52800 52813 72817 62838 62842
4 84001 52805 52814 72818 62839 62843
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
AVPA1HDCIEU_0121.indd 79 2008/01/21 12:50:12