Filter
Top Products
81
MANUAL SETUP
ADVANCED
OPERATION
■ THX set D)THX SET
Use to manually adjust the THX settings.
Surround back speaker distance
SB DIST.
Use this feature to optimize the surround sound field when
you have to place the surround back L/R speakers apart.
Choices: under 0.3m, 0.3 – 1.2m, over 1.2m
(under 1ft, 1 – 4ft, over 4ft)
• Select under 0.3m (under 1ft) if the distance between
the surround back L/R speakers is less than 0.3 m (1 ft).
• Select 0.3 – 1.2m (1 – 4ft) if the distance between the
surround back L/R speakers is between 0.3 and 1.2 m
(between 1 and 4 ft).
• Select over 1.2m (over 4ft) if the distance between the
surround back L/R speakers is more than 1.2 m (4 ft).
■ Test tone E)TEST TONE
Turns the test tone output on or off for the SPEAKER
SET, SP LEVEL and SP DISTANCE settings.
Choices: ON, OFF
y
If you use a handheld SPL meter, hold at arm’s length and point
upwards so that the meter is in the listening position. With the
meter set to the 70 dB scale and to C SLOW, calibrate each
speaker to 75 dB.
• This function is automatically turned off if you exit BASIC
MENU.
• If you select ON and enter the SPEAKER SET, SP LEVEL or
SP DISTANCE menu, the test tone is output from the selected
speakers.
Use to manually adjust speaker settings or compensate for
video signal processing delays when using LCD monitors
or projectors. Most of the SOUND MENU parameters are
set automatically when you run AUTO SETUP (see
page 32).
■ Graphic equalizer A)EQUALIZER
Use this feature to select parametric (PEQ) or graphic
equalizer (GEQ).
Equalizer select SELECT
Choices: AUTO PEQ, GEQ, EQ OFF
• Select AUTO PEQ to use the equalizer adjusted in
AUTO SETUP (see page 32).
• Select GEQ to adjust the built-in 7-band graphic
equalizer.
• Select EQ OFF to completely deactivate both PEQ and
GEQ.
• If GEQ is selected, the OSD automatically changes to the
graphic equalizer screen as shown below.
• AUTO PEQ is automatically selected if you run AUTO SETUP
(see page 32).
Graphic equalizer GEQ
Use to match the tonal quality of the center, surround L/R
and surround back L/R, surround back and presence L/R
speakers with that of the front L/R speakers.
Choices: –6 to +6 (dB)
You can adjust 7 frequency bands: 63Hz, 160Hz, 400Hz,
1kHz, 2.5kHz, 6.3kHz, 16kHz
The GEQ parameter can be adjusted only if GEQ is selected in
SELECT.
Notes
[<]/[>]:Adjust
SB DIST.
0.3-1.2m
D)THX SET
[<]/[>]:Select
TEST TONE;;;;OFF
E)TEST TONE
Using SOUND MENU
Notes
Note
. A)EQUALIZER
B)LFE LEVEL
C)DYNAMIC RANGE
D)AUDIO SET
2 SOUND
MENU 1/2
[]/[]:Up/Down
[ENTER]:Enter
p
p
. E)HDMI SET
2 SOUND
MENU 2/2
[]/[]:Up/Down
[ENTER]:Enter
p
p
. SELECT....GEQ
A)EQUALIZER
[<]/[>]:Adjust
[ENTER]:Enter
. CHANNEL;;FRONT L
-+
63Hz 0.0dB
160Hz 0.0dB
400Hz 0.0dB
A)EQUALIZER
[]/[]:Up/Down
[<]/[>]:Adjust
p
p