Sony BKDF-711 Stereo System User Manual


 
1-57
DFS-700/700P
Chapter 4 Advanced Operations
4-22
Chapter 4 Advanced Operations
Recalling a Snapshot
To recall a snapshot, use the following procedure.
1
To leave the primary cross-point bus section settings unaltered, press
the HOLD INPUT button, turning it on.
2
Press the RECALL button.
The button lights, and the pattern/numeric keypad is ready to accept a
snapshot number.
3
With the buttons 0 to 9, enter the snapshot number you want to recall.
You can use the UP and DOWN buttons to adjust the number
displayed.
4
Press the ENTER button.
This recalls the specified snapshot, and the control panel settings all
change correspondingly.
If, however, you turned the HOLD INPUT button on in step 1, the
settings of the primary cross-point bus section do not change.
Direct Snapshot Recall
You can recall snapshots 0 to 9 with a single button operation.
Snapshots
LAST X
INS
RST
TITLE
12
EDITOR LUM LUM LUM
DSK EDGE
TRAIL
SHADOW
GPI CRK CRK BORDERBEVELD
EDGE
SET UP MASK MASK MASK SOFT
SHIFT CCR LIGHTING BORDERMATTES
LOCATION
LEARNEDIT
RECALL
HOLD
INPUT
INITIAL
PATTERN
ADJ
PAGE
F1 F2 F3 F4 F5
USER PGM
STATUS EDIT
SNAP SHOT
SET
PATTERN NUMBER
EFFECT
DSK
FTB
SET
TRANS RATE
789
456
123
0
DOWN UP
ENTER
FADE
TO
BLACK
P IN P
DSK
DEL
N/R REV DSK PVWDIRECT
RECALL
DIRECT
PATTERN
CCR TITLE 1
SOURCE
TITLE 2
SOURCE
DSK
FILL
SUPER BGFRGD 2MEMORYFRAME FREEZ MIX EFFECT
BACKGROUND
BLACK MEMORY INT
VIDEO
TITLE
12345678
CUT
AUTO
TRANS
AUXILIARY
BLACK
MEMORY
INT
VIDEO
12345678
FOREGROUND
BLACK
MEMORY
INT
VIDEO
12345678
PATTERN/KEY PAD
1
2
3
4
SNAP SHOT number display
Chapter 4 Advanced Operations
Chapter 4 Advanced Operations
4-23
Use the following procedure.
1
In the pattern/numeric keypad, press the DIRECT RECALL button,
turning it on.
This switches to direct recall mode.
2
Press the one of buttons 0 to 9 corresponding to the snapshot you want
to recall.
This recalls the snapshot.
To cancel the snapshot recall operation
In step 4, press the LEARN button instead of the ENTER button. The
LEARN button goes out and the operation is canceled.
Returning to the previous image with the LAST X function
To return to the state before recalling a snapshot, use the following
procedure.
1
Press the RECALL button in the snapshot section, turning it on.
Alternatively, press the DIRECT RECALL button, turning it on.
2
Hold down the ENTER button in the pattern/numeric keypad, and
press the LAST X button.
Snapshot Demonstration
You can automatically show all of snapshots 0 to 99 in sequence.
You can use this function for checking the snapshots, and also in the same
manner as the factory setting demonstration (see page 3-8).
The snapshot registers and factory setting demonstration registers are
separate. Even after changing the settings in the snapshot registers, you can
still run the factory setting demonstration unchanged.
To start the demonstration
Hold down buttons 1 and 9 in the pattern/numeric keypad, and press the
AUTO TRANS button in the effect transition section.
This plays back the snapshots in sequence, starting from the snapshot
whose number is specified at the time. During the demonstration, the
buttons on the pattern/numeric keypad light in turn in the clockwise
direction.
•The HOLD INPUT button setting also applies to the demonstration.
•During the demonstration, the control panel does not accept any
operations other than pressing the AUTO TRANS button.
To end the demonstration
Press the AUTO TRANS button once more.