Filter
Top Products
PROGRAMMING THE REMOTE
TO CONTROL A VCR
To determine whether you need to program the
remote, turn on the VCR,point the remote at the VCR's
remote sensor, and press VCR.Then, pressthe POWER
orCH + orCH - buttontoseeiftheVCR respondsto
the remotecommands. Ifnot,you needtoprogram
the remote.
Follow these steps to program your remote to control
your VCR:
1. Turn on the VCR.
2. Look up your VCRbrand and code number(s)in the
code list on the next page or on the code sheet
packed with your remote.
3. Pressand hold the VCRbutton on
the remote.
4.
5.
Enter the three-digit code from the code list,
Releasethe VCR button, then pressPOWERto see
if the VCRresponds to the remote commands. If
not,trypressingVCR
thenPOWER.
6. Repeat steps3 through 5 using the next code listed
for your VCRbrand until the VCRresponds to the
remote commands.
PROGRAMMING THE REMOTE TO
CONTROL AN AUDIO COMPONENT
To program the remote for a remote-controllable
audio component, point the remote at the component
and pressthe correctcomponent button: CD for a CD
player, TAPEfor a tape player,etc. Then, pressPOWER
or CH + or CH -. If the component doesn't respond,
the remote needs to be programmed. Usethe codes in
the code list on the next page or on the sheet packed
with your remote.
Follow these stepsto program your remote to control
your audio component:
1. Turn on the component to be programmed.
2. Look up the brand and correspondingcode
number in the code list on page 28 or on the code
sheet packed with your remote.
3. Pressand hold the component button on
the remote.
4. Enter the three-digit code from the code list.
S,
Release the component button, then pressPOWER
to see if the component responds to the remote
commands. If it doesn't, try pressing the
component button, then POWERagain.
6. Repeat steps 3 through 5 using the next code listed
for the brand of your component until the
component responds to the remote commands.
PROGRAMMING THE REMOTE
TO CONTROL A CABLE BOX
Refer to the cable box connectionpage or contact your
cable companyto hook up your cable box. You may be
able to program the remote for your remote
controllable cable box. Usethe codes in the codelist
on page 28 or on the sheet packed with your remote.
1, Turn on the cable box.
2. Look up the cable box brand and its code
number(s) in the code list on the next page or on
thecodesheetpackedwiththeremote.
3. Pressand hold the SAT.CABLE button on
the remote.
4. Enter the three-digit code from the code list.
,
Releasethe SAT.CABLEbutton, then pressPOWER
or CH + or CH - to see if the cable box responds to
the remote commands. If not, try pressing
SAT.CABLE,then POWERagain to see if the cable
box responds.
6. Repeat steps 3 through 5 using the next code listed
for the brand of your cable box until the cable box
responds to the remote commands.
PROGRAMMING THE REMOTE
TO CONTROL A LASERDISC PLAYER
You maybe able to program your remote to control a
laserdiscplayer. Usethe codesshown to the right or on
the sheet packed with your remote.
Follow these stepsto program your remote to control
your laserdisc player:
1. Turn on the laserdisc player.
2. Look up the brand and its code number(s) in the
code list.
3. Pressand hold the LD-VCR2 button on the remote.
4. Enter the three-digit code from the code list.
LASERDISC PLAYER CODES 1
Pioneer .................................033,037
ProScan ................................033,037
RCA.......................................033,037
20