Filter
Top Products
Controlling the rest of your system
12
59
En
8 Repeat steps 5–7 to program a sequence of up to
five commands.
9 When you’re finished, use
/
to select EDITEXIT
from the menu and press
ENTER
.
You will return to the remote control SETUP menu. Select
* EXIT * again to exit.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
Using System off
1 Press MULTI OPE.
MULTI OP flashes in the display.
2Press
SOURCE
.
The command sequence you programmed will run, then
all Pioneer components will switch off
1
, followed by this
receiver.
Controls for TVs
This remote control can control components after
entering the proper codes or teaching the receiver the
commands (see Setting the remote to control other
components on page 57 for more on this). Use the input
source buttons to select the component.
•The TV CONTROL buttons on the remote control are
dedicated to control the TV assigned to the TV CTRL
button. If you have two TVs, assign the main TV to the
TV CTRL button.
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
SHIFT
AUDIO
DISP
SUBTITLE
MULTI OPE
HDD
CH
CH
DVD
RECEIVER
STEREO/
F.S.SURR
PHOTO
THX STANDARD
AUTO SURR
SIGNAL SEL
ADV.SURR
EFFECT/CH SEL LEVEL
ACOUSTIC EQ
RECEIVER
SOURCE
SYSTEM OFF
INPUT
SELECT
TV DVR 1
TV CTRL
DVD
DVR 2
SHIFT
AUDIO
DISP
SUBTITLE
MULTI OPE
HDD
CH
CH
DVD
RECEIVER
STEREO/
F.S.SURR
PHOTO
THX STANDARD
AUTO SURR
SIGNAL SEL
ADV.SURR
EFFECT/CH SEL LEVEL
ACOUSTIC EQ
Button(s) Function Components
TV
Press to switch the component
assigned to the TV CTRL
button on or off.
Cable TV/
Satellite TV/TV
INPUT
SELECT
Switches the TV input. (Not
possible with all models.)
TV
TV CH +/–
Selects channels. Cable TV/
Satellite TV/TV
TV VOL +/–
Adjust the TV volume. Cable TV/
Satellite TV/TV
SOURCE
Switches the TV or CATV
between standby and on.
Cable TV/
Satellite TV/TV
Use to choose the ‘A’
commands
on a Satellite TV
menu.
Satellite TV
Use to choose the RED/B
commands on a Satellite TV/TV
menu.
Satellite TV/TV
Use to choose the CYAN/E
commands on a Satellite TV/TV
menu.
Satellite TV/TV
Use to choose the GREEN/C
commands on a Satellite TV/TV
menu.
Satellite TV/TV
Use to choose the YELLOW/D
commands on a Satellite TV/TV
menu.
Satellite TV/TV
AUDIO
/
DISP
Use to switch audio tracks. Satellite TV/TV
SUBTITLE
Use to return to the previously
selected channel.
Cable TV/
Satellite TV/TV
GUIDE
Use as the GUIDE button for
navigating.
Cable TV/
Satellite TV/TV
RETURN
Use to select RETURN or EXIT. Satellite TV/TV
Number
buttons
Use to select a specific TV
channel.
Cable TV/
Satellite TV/TV
+10 button
Use to add a decimal point
when selecting a TV channel.
Satellite TV/TV
ENTER/
DISC
Use to enter a channel. Cable TV/
Satellite TV/TV
MENU
Select the menu screen. Cable TV/
Satellite TV/TV
///
& ENTER
Select, adjust and navigate
items on the menu screen.
Cable TV/
Satellite TV/TV
TOP MENU
Switches TEXT ON/OFF for TVs. TV
VSX-1017_HY.book Page 59 Tuesday, March 6, 2007 3:53 PM