Filter
Top Products
Other Settings
10
52
En
Chapter 10:
Other Settings
The Input Assign menu
You only need to make settings in the Input Assign menu
if you didn’t hook up your digital equipment according to
the default settings for the digital inputs, or if you have
connected equipment using component video cables.
1 Press
RECEIVER
on the remote control, then press
the
SETUP
button.
An on-screen display (OSD) appears on your TV. Use /
// and ENTER to navigate through the screens
and select menu items. Press RETURN to confirm and
exit the current menu.
2 Select ‘Input Assign’ from the System Setup menu.
Assigning the digital inputs
• Default settings:
Coaxial - 1 – DVD/LD
Coaxial - 2 – DVR 2
Optical - 1 – DVR 1
Optical - 2 – TV/SAT
Optical - 3 – CD
You only need to do this if you didn’t hook up your digital
equipment according to the default settings for the
digital inputs (see above). This setting tells the receiver
what digital equipment is hooked up to which terminal so
the buttons on the remote correspond to what you have
hooked up.
1 Select ‘Digital Input’ from the Input Assign menu.
2
Select the number of the digital input to
which
you’ve connected the digital component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
3 Select the component that corresponds with the
one you connected to that input.
Select between DVD/LD, TV/SAT, CD, CD-R, DVR 1,
DVR 2 or OFF.
•Use / and ENTER to do this.
• If you assign a digital input to a certain function (for
example, DVD/LD) then any digital inputs previously
assigned to that function will automatically be
switched off.
4 When you're finished, press RETURN.
You return to the Input Assign menu.
Assigning the component video inputs
• Default settings:
Component 1 – OFF
Component 2 – OFF
Component 3 – OFF
If you used component video cords to connect your video
equipment you must tell the receiver which device it is, or
else you may see the S-video or composite video input
instead of the component video signal. For more on this,
see Using the component video jacks on page 14.
1 Select ‘Component Input’ from the Input Assign
menu.
2 Select the number of the component video input to
which you’ve connected your video component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
3 Select the component that corresponds with the
one you connected to that input.
Select between DVD/LD, TV/SAT, DVR 1, DVR 2 or OFF.
•Use / and ENTER to do this.
• Make sure you have made audio connections from
the component to the corresponding inputs on the
rear of the receiver.
• If you connect any source component to the receiver
using a component video input, you should also have
your TV connected to this receiver’s component video
MONITOR output (downconverting component video
is not possible after assigning an input).
4 When you're finished, press RETURN.
You return to the Input Assign menu.
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
5.Input Assign
:Return
a.Digital Input
b.Component Input
c.HDMI Input
5.Input Assign
:Return
a.Digital Input
b.Component Input
c.HDMI Input
5a.Digital Input Setup
:Finish
Coaxial - 1
DVD/LD
Coaxial - 2 [ DVR 2 ]
Optical - 1 [ DVR 1 ]
Optical - 2 [ TV/SAT ]
Optical - 3 [ CD ]
5. Input Assign
:Return
a.Digital Input
b.Component Input
c.HDMI Input
5b.Component Input
:Finish
Component - 1
OFF
Component - 2 [ OFF ]
Component - 3 [ OFF ]
VSX-1017_HY.book Page 52 Tuesday, March 6, 2007 3:53 PM