Filter
Top Products
Using the tuner
07
48
En
Saving station presets
If you often listen to a particular radio station, it's
convenient to have the receiver store the frequency for
easy recall whenever you want to listen to that station.
This saves the effort of manually tuning in each time. This
unit can memorize up to 30 stations, stored in three
banks, or classes, (A, B and C) of 10 stations each. When
saving an FM frequency, the
MPX
setting (see page 47) is
also stored.
The illustration above shows the VSX-2014i model.
1 Tune to a station you want to memorize.
See
Listening to the radio
on page 47 for more on this.
2 Press T.EDIT (TUNER EDIT).
The display shows
STATION MEMORY
, then a blinking
memory class.
3 Press CLASS to select one of the three classes
then press ST +/– (STATION +/–) to select the station
preset you want.
You can also use the number buttons or the
MULTI JOG
dial (front panel) to select a station preset.
4 Press ENTER.
After pressing
ENTER
, the preset class and number stop
blinking and the receiver stores the station.
Naming station presets
For easier identification, you can name your station
presets.
1 Choose the station preset you want to name.
See
Listening to station presets
below for how to do this.
2 Press T.EDIT (TUNER EDIT).
The display shows
STATION NAME
, then a blinking
cursor at the first character position.
3 Input the name you want.
Choose from the following characters for a name up to
four characters long.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
0123456789
!”#$%&’()
∗
+,–./:;<=>?@[ \ ]^_{|} ˜
• Use the
MULTI JOG
dial (front panel) or the
ST +/–
buttons (remote) to select characters.
• Press
ENTER
to confirm a character. If no character
is input, a space is input.
• The name is stored when
ENTER
is pressed after
choosing the fourth character.
Tip
• To erase a station name, simply repeat steps 1-3 and
input four spaces instead of a name.
• Once you have named a station preset, you can press
TUNER
DISPLAY
when listening to a station to
switch the display between name and frequency.
Listening to station presets
You will need to have some presets stored to do this. See
Saving station presets
above if you haven’t done this
already.
1 Press TUNER to select the tuner.
2 Press CLASS to select the class in which the
station is stored.
Press repeatedly to cycle through classes A, B and C.
3 Press ST +/– (STATION +/–) to select the station
preset you want.
• You can also use the number buttons on the remote
control to recall the station preset.
Note
• If the receiver is left disconnected from the AC power
outlet for over a month, the station memories will be
lost and will have to be reprogrammed.
STANDBY/ON
MULTI JOG
LISTENING MODE
SELECT
ENTER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP
RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S
-
VIDEO VIDEO
VIDEO2 INPUT
AUDIOLR
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION
BAND TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE
SPEAKERS
MULTI
JOG
MULTI
JOG
PTY
SEARCH
EON
i.LINK
SELECT
MULTI
JOG
MULTI
JOG
INPUT ATT FL DIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
DVD/LD TV/SAT DVR/VCR TV CONT
CD
CD-R/TAPE
TUNER RECEIVER
+
10
INPUT ATT FL DIMMER SR
DISC
ENTER
TV CONTROL
VOL
TUNE
TUNE
INPUT
SELECT
TV CH
TUNER
DISPLAY
MPX
AUDIO
CH RETURN
SUBTITLE
REC MUTE
TV VOL
ENTER
REC STOP
HDD
CH
CH
DVD
D.ACCESS
TOP MENU
CLASS
MENU
BAND
RETURN
GUIDE
T.EDIT
SYSTEM
SETUP
A
BCDE
ST ST
VSX_2014TX.book.fm Page 48 Wednesday, June 2, 2004 5:21 PM