Filter
Top Products
5
RQT9129
∫ Notes on speaker use
≥Use only supplied speakers
Using other speakers can damage the unit, and sound quality will be
negatively affected.
≥You can damage your speakers and shorten their useful life if you
play sound at high levels over extended periods.
≥Reduce the volume in the following cases to avoid damage:
–When playing distorted sound.
–When the speakers are reverberating due to a record player, noise
from FM broadcasts, or continuous signals from an oscillator, test
disc, or electronic instrument.
–When adjusting the sound quality.
–When turning the unit on or off.
∫ If irregular coloring occurs on your TV
The front and center speakers are designed to be used close to a TV,
but the picture may be affected with some TVs and setup
combinations.
If this occurs, turn the TV off for about 30 minutes.
The demagnetizing function of the TV should correct the problem. If it
persists, move the speakers further away from the TV.
∫ Caution
Do not touch the front netted area of the speakers. Hold by the sides.
e.g., Center speaker
You can attach all of the speakers (except subwoofer) to a wall.
≥The wall or pillar on which the speakers are to be attached should
be capable of supporting 10 kg (22 lbs) per screw. Consult a
qualified building contractor when attaching the speakers to a wall.
Improper attachment may result in damage to the wall and
speakers.
1 Detach stand (Front/Surround speakers).
2 Drive a screw (not included) into the wall.
≥Center/Front/Surround speaker
Ensure that the screw is positioned at least 70 mm (2
3
/4q) away
from the ceiling.
≥Center speaker
Ensure that the screw is positioned at least 100 mm (3
15
/16q)
away from the wall.
Fixing the position for the center speaker screws.
1 Drive in a screw 50.5 mm (2q) left of
the right side of the center speaker
as seen directly from the front.
2 Drive another screw 160 mm
(6
5
/16q) left of the first screw.
3 Fit the speaker securely onto the screw(s) with
the hole(s).
(Except subwoofer)
Ensure the stands meet these conditions before purchasing them.
Note the diameter and length of the screws and the distance between
screws as shown in the diagram.
≥The stands must be able to support over 10 kg (22 lbs).
≥The stands must be stable even if the speakers are in a high
position.
e.g., Center speaker
≥You will need to obtain the appropriate screw eyes to match the walls
and pillars to which they are going to be fastened.
≥Consult a qualified housing contractor concerning the appropriate
procedure when attaching to a concrete wall or a surface that may
not have strong enough support. Improper attachment may result in
damage to the wall or speakers.
Speaker installation options
Attaching to a wall
Do
Do not
Remove the
3 screws
‰7.5 mm to 9.4 mm
(
19
/64q to
3
/8q)
7.0 mm to 9.4 mm (
9
/32q to
3
/8q)
Wall or pillar
‰4.0 mm (
5
/32q)
At least 30 mm (1
3
/16q)
Fitting speaker stands (not included)
Prevent the speakers from falling
Front/Surround speaker
Center speaker
e.g.,
In this position, the
speaker will likely fall
if moved to the left or
right.
Do
Do not
Move the speaker
so that the screw is
in this position.
5.0 mm (
3
/16q), pitch 0.8 mm (
1
/32q)
60 mm (2
3
/8q)
Plate thickness plus 7 mm to
10 mm
(plus
9
/32q to
13
/32q)
Metal screw holes
For attaching to
speaker stands
Speaker stand
(not included)
String (not included)
Thread from the wall to the
speaker and tie tightly.
Approx.
150 mm
(5
29
/32z)
Rear of the speaker
Wall
Screw eye
(not included)
e.g., Front speaker
Quick Start Guide
Getting started
SC-BT100P-ENG.book 5 ページ ２００８年２月２０日 水曜日 午後６時２２分