Filter
Top Products
89
Controlling Other Components—Continued
The AV receiver’s remote controller can receive and
learn commands from other remote controllers. By trans-
mitting, for example, the Play command from your CD
player’s remote controller, the remote controller can
learn it and then transmit the exact same command when
its Play [ ] button is pressed in the CD remote mode.
You can also use this function to learn individual com-
mands after entering a remote control code (page 86).
Notes:
• The following buttons cannot learn new commands:
REMOTE MODE, MACRO [1], [2], [3], TV [ ],
TV [INPUT], TV CH [+]/[–], TV VOL [ ]/[ ],
Light.
• The remote controller can learn approximately 70-90
commands, although, this will be reduced by com-
mands that use a lot of memory.
• Remote controller buttons such as Play, Stop, Pause,
and so on are preprogrammed with commands for
controlling Onkyo CD players, cassette decks, and
DVD players. However, they can learn new com-
mands, and you can restore the preprogrammed com-
mands by resetting the remote controller (see
page 87).
•To overwrite a previously learned command, repeat
this procedure.
• Only commands from infrared remote controllers can
be learned.
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
Learning Commands from Other
Remote Controllers
1
While holding down the REMOTE
MODE button for the mode in
which you want to use the com-
mand, press the [ON] button.
The Remote indicator lights up.
2
On this AV receiver’s remote con-
troller, press the button you want
to learn the new command.
10
--/---
11 12
REMOTE MODE
HDD
RECEIVER
TAPE/AMP
DVD CD
ZONE2
SAT
TV
VCR
CABLE
MDCDR
+
-
T
V CH
T
V VOL
ENTER
S
E
T
U
P
T
O
P
M
E
N
U
M
E
N
U
VOL
+
-
CH
DISPLAY
PREV
CH
DIMMER
SLEEP
MUTING
INPUT SELECTOR
32
MACRO
1
+
10 0
CLEAR
12
3
456
789
INPUT
I
ON STANDBY
T
V
CD
V1 V2 V3
MULTI CH
DVD
TUNER
PHONO
DISC
ALBUM
V4
TAPE
R
E
T
U
R
N
1, 4
1
Remote
indicator
REMOTE MODE
HDD
RECEIVER
TAPE/AMP
DVD
CD
SAT
TV
VCR
CABLE
MDCDR
ON
3
Point the remote controllers at
each other, about 2 to 6 inches
(5–15 cm) apart, and then press
and hold the button whose com-
mand you want to learn until the
Remote indicator flashes.
If the command is learned successfully,
the Remote indicator flashes twice.
4
To learn more commands, repeat
steps 2 and 3.
Press any REMOTE MODE button
when you’ve finished.
POWER
SLEEP
DIMM
ER
SUR
MODE
VIDEO-1
VIDEO-2
TAPE
DVD
C D
C D
DVD
TU
NER
TUNER
PHONO
INPUT SELECTOR
DISC
TAPE
VOLUME
EVEL
CH SEL
PRESET
MUTING
TEST
TONE
MULTI-CH
INPUT
GROUP
R
1
0
-
-
/-
--
1
1
1
2
R
EM
O
TE M
O
DE
HDD
RE
CEIVER
P
E/AMP
DVD
CD
Z
O
N
E
2
SAT
VCR
C
ABLE
MD
CDR
+
-
T
V
C
H
T
V
V
O
L
M
E
N
U
SLEEP
INPUT SELECTOR
3
2
MACRO
1
+
10
0
CLEAR
1
2
3
4
5
6
7
8
9
IN
P
U
T
I
O
N
S
T
A
N
D
B
Y
T
V
C
D
V
1
V
2
V
3
MULTI CH
D
V
D
T
A
P
E
T
U
NE
R
PHONO
V
4
About 2 to 6
inches (5–15 cm)
RC-620M