Onkyo SR804 Stereo Receiver User Manual


 
42
First Time Setup—Continued
Checking the Results
If you selected “Check the Results” in step 4 on the pre-
vious page, the following menu appears and you can
check the results of the automatic speaker setup.
1. Warning—Undetected speakers and position warn-
ings (see the right column).
2. Speaker Config—Connected speakers and crossover
frequencies.
3. Speaker Distance—Distance from each speaker to
the listening position.
4. Speaker Level Adjust—Optimum volume level for
each speaker.
5. Equalizer Settings—Optimum equalizer settings for
each speaker.
Warning Messages
In the warning messages, abbreviations are used to iden-
tify the speakers (e.g., “L” for left, “R” for right, and so
on).
Not Detect:
The speaker was not detected. Make sure that it’s
connected properly.
Distance Error:
The speaker is either too close or too far away, or
the distance could not be measured. Reposition the
speaker.
Changing the Speaker Settings Manually:
In some situations, the measurements taken by the auto-
matic speaker setup may not provide usable results. If
running the speaker setup a second time still doesn’t pro-
vide usable results, you’ll have to set the speaker settings
yourself (see pages 70–75).
Please note that any THX main speakers should be set to
80 Hz (THX). If you set up your speakers using Auto-
matic Speaker Setup, please make sure manually that
any THX speakers are set to 80 Hz (THX) in the Speaker
Configuration setting (see pages 70, 71).
Sometimes due to the electrical complexities of sub-
woofers and the interaction with the room, THX recom-
mends setting the level and the distance of the subwoofer
manually.
Using a Powered Subwoofer:
If you’re using a powered subwoofer, because it’s posi-
tioned low down on the floor and outputting very low
frequency sounds, its output may not be detected prop-
erly. If the subwoofer (abbreviation “SW”) appears on
the Warning screen under Not Detect, turn up the sub-
woofer’s volume and run the automatic speaker setup
again. If the subwoofer has a built-in crossover, set it to
the highest crossover frequency. If it has an LPF filter
switch, set it to off or direct. Refer to your subwoofer’s
instruction manual for details.
Use the Up and Down [ ]/[ ]
buttons to select the item that
you want to check, and then
press [ENTER].
Press the [RETURN] button to return to
the previous menu.
Auto Speaker Setup
========================
1.Warning
2.Speaker Config
3.Speaker Distance
4.Speaker Level Adjust
5.Equalizer Settings
ENTER
ENTER
1.Warning
========================
Not Detect:
Distance Error:
2.Speaker Config
========================
Front :80Hz(THX)
Center :80Hz(THX)
Surround :80Hz(THX)
SurrBack :80Hz(THX)
SurrBack ch :2ch
Subwoofer :No
3.Speaker Distance
========================
Left :12ft
Center :12ft
Right :12ft
Surround R : 7ft
SurrBack : 7ft
Surround L : 7ft
Subwoofer :12ft
4.Speaker Level Adjust
========================
Left : 0dB
Center : 0dB
Right : 0dB
Surround R : 0dB
SurrBack : 0dB
Surround L : 0dB
Subwoofer : 0dB
5.Equalizer Setting
========================
========================
80Hz : 0dB
250Hz : 0dB
800Hz : 0dB
2.5kHz : 0dB
8kHz : 0dB
Channel: Left
When you’ve finished checking,
press the [RETURN] button to
return to the menu in step 4.
Auto Speaker Setup
========================
Apply the Results
Check the Results
Retry
Retry with
Test noise Level up
Cancel