Filter
Top Products
59
Operating Other Manufacturers’ Equipment
This remote control supplied with the receiver can transmit control signals for other manufacturers’ TVs, CATV
converters, DBS tuners, VCRs and DVD players.
• Refer also to the manuals supplied with your video components.
By changing the transmittable signals from preset ones to the other
manufacturers’, you can operate the other manufacturer’s
components using this remote control.
To change the transmittable signals for
operating another manufacturer’s TV
1. Set the TV operation mode
selector to TV.
2. Press and hold
TV/CATV/DBS POWER.
3. Press TV/DBS.
4. Enter a manufacturer’s code
using buttons 1–9, and 0.
See page 62 to find the code.
5. Release
TV/CATV/DBS POWER.
6. Try to operate your TV by
pressing
TV/CATV/DBS POWER.
When your TV turns on or off, you have
entered the correct code.
If more than one code is listed for
your brand of TV, try each one until the
correct one is entered.
After setting the TV operation mode
selector to TV, you can perform the following operations on the
TV:
TV/CATV/DBS POWER
: Turn on or off the TV.
TV VOL +/– : Adjust the volume.
TV/VIDEO : Set the input mode (either TV or
VIDEO).
After pressing TV/DBS (with the TV operation mode selector
set to TV), you can perform the following operations on the TV:
CHANNEL +/– : Change the channels.
1 – 9, 0, 100+ (+10) : Select the channels.
RETURN (10) : Alternates between the previously
selected channel and the current
channel.
Notes:
• Refer to the manual supplied for the TV.
• Some buttons listed above may not be used for some TVs.
• If you cannot change the channels of some TVs by pressing
number buttons, press the CHANNEL +/– buttons.
IMPORTANT:
• To operate the other component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
–Place the IR signal transmitter so that it is aimed at the remote
sensor(s) on the target component(s).
–The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
–The IR signal transmitter can send signals at a distance of 3 m
(10 feet).
When using the remote control:
–Set the ZONE 1/ZONE 2 selector to ZONE 1 or ZONE 2 correctly.
–Set the TV operation mode selector to TV or
CATV/DBS correctly.
To operate the TV, set it to TV.
To operate the CATV converter or DBS tuner, set it to
CATV/DBS.
–Check the indication shown on the remote’s display when you press
a button—this indicates the remote control operation mode together
with multi-room operation mode (either for ZONE 1 or ZONE 2) for
about two hours.
TV
CATV/
DBS
Ex. When you press DVD with
ZONE 1/ZONE 2 selector
set to ZONE 1.
Ex. When you press DVD with
ZONE 1/ZONE 2 selector
set to ZONE 2.
Note:
When replacing the batteries, finish changing them without delay;
otherwise, preset manufacturers’ codes will be reset.
ZONE 2
ZONE 1
ZONE 2
ZONE 1
ON/OFF ON/OFF
AUDIO POWER
TV/CATV/DBS DVD
ZONE 2
ZONE 1
ZONE 2
ZONE 1
POWER POWER
STANDBY
ON
ZONE 1
ON/OFF ON/OFF
AUDIO POWER
TV/CATV/DBS DVD
ZONE 2
ZONE 1
ZONE 2
ZONE 1
POWER POWER
STANDBY
ON
ZONE2
CHANNEL
TV/VIDEO
TV/CATV/DBS
RETURN
TV VOL
TV/DBS
TV
123
456
7
/P
89
10
+
100
POWER
Ex. When you set ZONE 1/
ZONE 2 selector to ZONE 1.
Ex. When you set ZONE 1/
ZONE 2 selector to ZONE 2.