Filter
Top Products
33
English
Activating the Surround Modes
Available Surround modes vary depending on the speaker settings
and the incoming signals. (See page 32.)
Activating one of the Surround modes for a source automatically
recalls the memorized settings and adjustments (see pages 21 to
29).
You can also use the buttons on the remote control for the same
functions.
Activating the EX/ES setting
For multi-channel digital software, you can activate the EX/ES (7.1-
channel) reproduction mode.
• Once you have set EX/ES (7.1-channel) reproduction mode, it is
stored in memory and will be called up whenever you activate the
Surround mode which the memorized EX/ES (7.1-channel)
reproduction mode can be applied to.
Press EX/ES to select an appropriate setting for your enjoyment.
The currently selected EX/ES (7.1-channel) reproduction mode
appears on the display.
• Each time you press the button, it changes as follows:
For details of applicable Surround mode, see “Surround Modes
Applicable to the Various Software” on page 32.
EX/ES AUTO According to the incoming signal, an
appropriate Surround mode is applied.
• For Dolby Digital EX and DTS-ES,
EX/ES (7.1-channel) reproduction is applied.
• For other multi-channel (5.1-channel or less)
encoded software, 5.1-channel reproduction
is applied.
EX/ES ON Select to apply EX/ES (7.1-channel)
reproduction to both 5.1-channel and 6.1-
channel encoded software.
EX/ES OFF Select to cancel the EX/ES (7.1-channel)
reproduction.
Notes:
• When an analog or digital 2-channel source is playing, you can
adjust the EX/ES (7.1-channel) reproduction mode and store the
setting, but it will not affect the current source.
• When the source is one to which the EX/ES (7.1-channel)
reproduction cannot be applied, you can adjust the setting and store
in memory, but reproduction channels will remain unchanged.
• When the surround speakers are deactivated, you cannot activate
this setting and “NO SURR SP” appears on the display.
Activating the surround modes automatically
You can enjoy the Surround mode simply by selecting the source
(with digital input selected for that source) or select the digital input
for the selected source.
To activate Auto Surround, see page 25.
Activating the surround modes manually
1. Select and play any source other than DVD
MULTI.
• Make sure you have selected the analog or digital input mode
correctly.
• Surround modes are not valid for DVD MULTI playback
mode.
2. Press SURROUND to activate the Surround
mode.
• For multi-channel digital software, incoming signals are
automatically detected and the appropriate Surround mode is
activated (see page 32 for details).
– If the EX/ES (7.1-channel) reproduction mode has been set
to “AUTO” or “ON,” one of the EX/ES (7.1-channel)
reproduction modes will be activated (see the left column).
• For analog sources and digital 2-channel software, you can
select one of the following Surround modes. Each time you
press SURROUND, the Surround modes change as follows:
• For Dual Mono software, you can select the channel you
listen to. (See page 25.)
To adjust the speaker output level, see pages 28 and 29.
To cancel the surround modes
Press SURROUND/DSP OFF (or SURR/DSP OFF on the remote
control) repeatedly until “SURR OFF” appears on the display.
Ex. When “DOLBY D” is activated.
LINEAR PCM
DIGITAL
L
SUBWFR
LS RS
CR
LFE
DIGITAL
AUTO
VOLUME
SPEAKERS 1
LINEAR PCM
DIGITAL
L
SUBWFR
DUAL DIGITAL
AUTO
VOLUME
SPEAKERS 1
LINEAR PCM
L
SUBWFR
R
ANALOG
VOLUME
PRO LOGIC
SPEAKERS 1
(CINEMA)
NEO:6CINMANEO:6MUSIC
PL
II
MOVIE PL
II
MUSIC PRO LOGIC
30-36_7040[C] 04.2.12, 19:0133