Filter
Top Products
15
English
Selecting the Front Speakers
When you have connected two pairs of the front speakers, you can
select which to use.
To use the speakers connected to the FRONT SPEAKERS 1
terminals, press SPEAKERS ON/OFF 1 so that the SPEAKERS 1
indicator lights up on the display.
• Make sure that the SPEAKERS 2 indicator is not lit.
To use the speakers connected to the FRONT SPEAKERS 2
terminals, press SPEAKERS ON/OFF 2 so that the SPEAKERS 2
indicator lights up on the display.
• Make sure that the SPEAKERS 1 indicator is not lit.
To use both sets of the speakers connected to the FRONT
SPEAKERS 1 and 2 terminals, press SPEAKERS ON/OFF 1
and 2 so that the SPEAKERS 1/2 indicators light up on the display.
Note:
When playback analog sources or digital 2-channel software and
neither Surround/DSP mode is selected, you can use both sets of the
front speakers.
To use neither sets of the speakers connected to the FRONT
SPEAKERS 1 and 2 terminals, press SPEAKERS ON/OFF 1
and 2 so that the SPEAKERS 1/2 indicators go off from the display.
The HEADPHONE indicator lights up and “HEADPHONE”
appears on the display.
• Activating the speakers turns on the Surround and DSP modes
previously selected.
Listening with headphones only:
Deactivate both sets of the front speakers, and connect headphones
to the PHONES jack.
• Make sure that all the Speaker indicators are not lit.
You can enjoy the sound effects through the headphones when
Surround or DSP mode is activated—3D Headphone
(3D H PHONE) mode.
•“3D H PHONE” appears and the DSP and HEADPHONE
indicators light up on the display. (For details, see page 32.)
Note:
3D Headphone (3D H PHONE) mode is not valid for DVD MULTI
playback mode.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones, as its high volume can
damage both the headphones and your hearing.
• Before turning on the speakers again, as its high volume may come
out of the speakers.
Continued on the next page
Remote
NOT
Turning On and Off the
Subwoofer Sound
You can cancel the subwoofer sound output even though you have
connected a subwoofer and have set “SUB WOOFER” to “YES”
(see page 23).
Press SUBWOOFER OUT ON/OFF to cancel the subwoofer
sound output.
Each time you press the button, subwoofer sound output is
deactivated (“SUBWFR OFF”) and activated (“SUBWFR ON”)
alternately.
• When subwoofer output is canceled, the
SUBWFR
indicator goes
off. Bass sounds (and LFE signals) will be emitted through the
front speakers (except for DVD MULTI playback mode).
• When subwoofer sound output is activated, subwoofer output level
can be adjusted (see pages 28 and 29).
Notes:
• SUBWOOFER OUT ON/OFF button does not work when you set
“SMALL” for the front speakers on the Speaker size setting (see
page 23) or using Quick Speaker Setup (see page 21).
• You cannot activate the subwoofer output when you have set “SUB
WOOFER” to “NO” (see pages 21 and 23).
• When you change the “SUB WOOFER” setting from “NO” to “YES”
(see page 23), subwoofer output is automatically activated.
Selecting the Analog or Digital Input Mode
When you have connected digital source components using the
digital terminals (see page 12), change the input mode for these
components to the digital input mode.
Before you start, remember...
The digital input terminal setting should be correctly done for
the sources you want to select the digital input mode (see
“Setting the digital input terminals” on pages 25 and 26).
1. Press one of the source selection buttons (DVD, VCR,
TV SOUND/DBS, CD, or TAPE/CDR*) for which you
want to change the input mode.
*
If TAPE is selected as the source, digital input mode is not
available. To change the source name to CDR, see “Changing
the Source Name” on page 17.
LINEAR PCM
L
R
ANALOG
VOLUME
SPEAKERS 1 2
Ex. When both sets of the speakers selected.
Remote
NOT
13-18_7040[C] 04.2.12, 19:0115