Filter
Top Products
GB-10[ENGLISH]
Setting the night mode
When the volume is set to a low level, for example, at night, setting the
night mode to “ON” will make sounds at low-volume levels easy to hear.
If you do not want sudden and drastic sound level changes due to
explosive sounds etc., setting this mode to “ON” will reduce extreme
sound level changes.
Press the NIGHT button.
The FL display becomes dimmer than usual. “NIGHT ON” is shown on the
FL display and the “NIGHT” indication in red letters lights up.
To set the night mode to “OFF”, press the NIGHT button again.
About Input/Output channel indicators (L, C, R, SW,
LS, RS)
These indicators are switched to the input channel display or output
channel display by the function or audio signal format.
Function: DVD/CD, V1 OPT, V2 COAX
Audio signal format: Display mode
PCM: Displays speaker output channel (Output display)
Dolby Digital: Displays the original channel (Input display)
DTS: Displays the original channel (Input display)
MP3/WMA: Displays speaker output channel (Output display)
Function: TV, VIDEO1, VIDEO2, FM TUNER, AM TUNER
Audio signal format: Display mode
Analog: Displays speaker output channel (Output display)
Note:
- When headphones are connected in the output display mode, “L” and
“R” remain lit only.
- Output and Input display modes are not switch by manual.
- When “SW” appears in the input display, LFE (Low Frequency Effect)
channel is included in the audio source.
Adjusting the FL display brightness
While pressing the ON SCREEN button on the remote control, press the
n button on the main unit.
NORMAL (Normal)
wv
DARK (Dark)
Locking the disc tray
It is possible to lock the disc tray in order to prevent children from misusing
it.
With the disc tray opened by pressing the q button, press and hold the q
button on the main unit until “LOCKED” appears on the FL display.
As a result, it becomes impossible to open the disc tray by pressing the q
button.
- To release the disc tray lock, press and hold the q button on the main
unit until “UNLOCKED” appears on the FL display.
- When the q button is pressed while the disc tray is locked, “DISC
TRAY LOCKED” appears on the TV screen and “LOCKED” appears
on the FL display.
Adjusting the volume balance of the front, centre
and surround speakers
This unit is set to the standard level at the factory before shipping. In order
to enjoy a more effectual surround-sound effect, adjust the volume
balance of each speaker according to the size of the room and the
placement of the speakers.
Preparation:
- Power on the TV and select the video input connected to the unit.
- If a disc is being played back, press the n button twice to stop the
playback completely.
- Disconnect the headphones if connected.
1. Select “DVD/CD” by pressing the FUNCTION button.
2. Press the TEST button. The “TEST TONE” screen appears on the TV
screen.
“L” blinks and “FNTL 0” appears on the FL display.
The test tone is heard from the speakers in the following sequence
with the display changing every approx. 2 seconds.
TV screen (FL display): Speaker
L ([L] FNTL 0): Front left speaker
C ([C] CENT 0): Centre speaker
R ([R] FNTR 0): Front right speaker
RS ([RS] SURR 0): Surround right speaker
LS ([LS] SURL 0): Surround left speaker
3.
Adjust the volume of the total test tone by pressing the VOL “+” or “–”
button.
4. Press the b / a button while the test tone is heard from the speaker
whose volume is to be adjusted.
At the listening position, make adjustments so that the volumes of the
test tones heard from all the speakers become the same.
The level is shown on the TV screen and the FL display.
Adjustable range:
L, R : –10 to 0
C, RS, LS : –10 to +10
If necessary, repeat this step.
5. Press the TEST button. The “TEST TONE” screen disappears.
Note:
After the test tone is heard from each speaker five times, speaker setting
ends automatically.
Adjusting the subwoofer level
- Disconnect the headphones if connected.
1. Press the TRIM button. “FNTL 0” appears on the FL display.
2. Select “SUBW 0” by pressing the ENTER button.
3. Press the b / a button to adjust the level as desired.
Adjustable range:
SUBW : –10 to +10
4. Press the TRIM button. The displayed speaker and level disappear.
Note:
- In the case of adjusting the subwoofer level, the test tone does not
sound. It is recommended to adjust the subwoofer level while playing
back music, etc.
- If no button is operated for approx. 15 seconds during setting, the
speaker setting ends automatically.
TEST TONE
LEVEL : B A QUIT : TEST
L
0
0
LS
C
0
R
0
0
RS