Filter
Top Products
SC3100
Introduction
SC3100 Operation and Installation Guide
© 2004 Bosch Security Systems Page 9 90026-201D
1.6.4 Federal Communications Commission (FCC) Statement
This equipment generates and uses radio frequency (RF) energy. If not installed and used properly, that is, in
strict accordance with the manufacturer's instructions, it may cause interference to radio or television reception.
This equipment has been tested and certified to comply with the specifications for a Class B digital device,
pursuant to Subpart J of Part 15 of FCC rules. These specifications are designed to provide reasonable
protection against such interference. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment on and off, the user is encouraged to correct the interference by one or more of the following
measures:
• Reorient the radio/television receiving antenna.
• Move the antenna leads away from any wire runs to the SAFECOM system.
• If using an indoor antenna, have a quality outdoor antenna installed.
• Relocate the SAFECOM system with respect to the radio/television receiver.
• Connect the host alarm panel's AC transformer to a different outlet so the SAFECOM system and the
radio/television are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions. The user might find the following booklet prepared by the Federal Communications Commission
helpful: "How to Identify and Resolve Radio-TV Interference Problems". This booklet is available from the US
Government Printing Office, Washington D.C. 20402. Stock No. 004-000-00345-4.
Properly shielded and grounded cables and connectors must be used for connection to peripherals in order to
meet FCC emission limits. Bosch Security Systems is not responsible for any radio or television interference
caused by using other than recommended cables or by unauthorized modifications to this equipment. It is the
responsibility of the user to correct such interference.
1.6.5 Federal Communications Commission (FCC) Notice To Users
1. Upon request only
, the telephone company (TELCO) must be provided with a notice of intention to install or
permanently remove the SC3100, along with the following information:
a) Manufacturer: Bosch Security Systems
b) Model Number: SC3100
c) FCC Registration Number: 1 L3USA-73968-MO-N
d) Ringer equivalence: 0.0A
e) Type of Jack: (USOC) RJ31 X, RJ32X, or equivalent
Note: The SC3100 is intended to be used in conjunction with Alarm Dialing Systems, and makes use of the RJ31X,
RJ32X, or equivalent jack required for such systems. An equivalent jack is one which, when the system is
disconnected from the jack, will continue to allow proper operation of the customer's telephone equipment.
2. The SC3100 may not be connected to a TELCO-operated coin telephone line. Connection to privately-
operated coin telephones is subject to local or state regulation, but is not recommended by the
manufacturer.
3. The TELCO may, under certain circumstances, temporarily discontinue service and/ or make changes in its
facilities or its service which may influence the operation of the SC3100. However, the telephone company is
required to give adequate notice in writing of such changes or service interruptions.
4. In case of operational problems, disconnect the SC3100 (and Alarm Dialing System) from the TELCO line
by removing the modular plug from the TELCO jack:
• If, after disconnecting the equipment from the TELCO jack, the customer’s regular phone operation has not
been restored, notify the telephone company that they may have a problem, and request prompt service at
no cost to the user. If a problem is found in premises wiring not installed by the TELCO, the customer will
be subject to a service charge. If a fault is found in wiring installed by the TELCO, the customer may be
subject to a service call charge.
• If, after disconnecting the equipment from the TELCO jack, the customer’s regular phone operation returns
to normal, the equipment must remain disconnected until the SC3100, Alarm Dialing Equipment, or related
wiring is serviced or replaced.
Unless otherwise noted in the Installation Guide (e.g., battery replacement, etc.), the SC3100 may not under any
circumstances (in or out of warranty) be adjusted or repaired in the field. The location and phone number of the
manufacturer, Bosch Security Systems, is listed in this guide.