Filter
Top Products
34 En
1 Press ISETUP.
2 Press G / to select the desired menu
and then press GENTER.
y
• To return to the previous menu, press IRETURN.
3 Press G / / / and GENTER to
configure each parameter.
y
• The initial settings are marked with “*”.
Note
• The menu screen disappears if one of the DInput selector
keys is pressed while the SET MENU is being configured.
4 To exit from the menu, press ISETUP.
Use this menu to manually adjust the parameters related to
the sound beam output. To fine-adjust parameters
configured by AUTO SETUP, use “BEAM
ADJUSTMENT” and “IMAGE LOCATION”.
■ SETTING PARAMETERS (Setting
parameters)
SET MENU → MANUAL SETUP → SETTING
PARAMETERS
Use to set the position of this unit in your listening room
and the distance of this unit from the listening position.
y
• If you make adjustments in “SETTING PARAMETERS”, the
“BEAM ADJUSTMENT” parameters are automatically
adjusted.
Note
• If you make adjustments in “SETTING PARAMETERS”, the
beam optimization settings made in the AUTO SETUP
procedure will be lost.
1 In “SETTING PARAMETERS 1/3”, configure
“INSTALLED POSITION”.
Select the installed position of this unit.
Choices: FLAT TO WALL* (parallel to wall),
ANGLE TO WALL OR CORNER (angle to wall or
corner)
Note
• If you change this setting, “BEAM MODE” setting
changes automatically (page 23).
2 Configure “INSTALLED HEIGHT”.
Specify the installed height of this unit.
Control range: 0.0 m to 3.0 m (0.0 ft to 10.0 ft)
Initial setting: 1.0 m (3.5 ft)
y
• Press G to proceed to the next page.
3 In “SETTING PARAMETERS 2/3”, configure
the listening room settings.
Specify the length and width of the listening room.
Control range: 2.0 m to 12.0 m (6.5 ft to 40.0 ft)
4 In “SETTING PARAMETERS 3/3”, configure
the distance settings.
Specify the distance between the listening position
and this unit. When this unit is installed parallel to
wall, you also need to specify the distance between
the listening position and left wall.
Basic SET MENU operation
MANUAL SETUP
;MEMORY
;AUTO SETUP
;MANUAL SETUP
;SOUND SET MENU
;SOUND OUT MENU
;INPUT MENU
;DISPLAY MENU
[ ]/[ ]:Up/Down
[ENTER]:Enter
SET MENU
.
p
p
1)SETTING PARAMETERS
2)BEAM ADJUSTMENT
3)IMAGE LOCATION
[ ]/[ ]:Up/Down
[ENTER]:Enter
C)MANUAL SETUP
p
p
.
FLAT TO WALL
ANGLE TO WALL OR
CORNER
0.0 to 3.0 m
(0.0 ft to 10.0 ft
)
When this unit is
installed parallel to wall,
specify the width of the
listening room and the
distance between this
unit and rear wall.
When this unit is
installed at the corner of
the room, specify the
width of length of the
listening room.
DInput selector keys
GENTER
G / / /
G /
G
IRETURN
ISETUP
0 +10
ENT
7 8 9
4 5 6
1 2 3
HDMI 4 iPod RADIO
ENTER
SURROUND STEREO
OFF
ENTER
TAINMENT
MUSIC
CINEMA DSP
MOVIE
HDMI 1 HDMI 2 HDMI 3
TV AUX 1 AUX 2
TV AV
MENUTOP MENU
OPTION
TV
MUTE
CODE SET
UNIVOLUME SUR. DECODE INTELLIBEAM
TV
INPUT MUTE
TV VOL CH VOLUME
SETUP RETURN
MEMORY
SLEEPINFO
TUNING PRESET CATEGORY
OPTION SETUP RETURN
I
ENTER
G
HDMI 4 iPod RADIO
HDMI 1 HDMI 2 HDMI 3
TV AUX 1 AUX 2
D