Filter
Top Products
16 En
■ Assembling the supplied cardboard
microphone stand
y
• If a subwoofer with adjustable volume and crossover frequency
controls is connected to this unit, turn it on, set the volume to
about half way and then set the crossover frequency to the
maximum as shown below.
You can select one of the following AUTO SETUP types
depending on your purpose.
“BEAM+SOUND OPTIMZ”
“BEAM OPTIMZ ONLY”
“SOUND OPTIMZ ONLY”
Notes
• It is normal for loud test tones to be output during the AUTO
SETUP procedure. Make sure that there are no children around
in the listening room while the AUTO SETUP procedure is in
progress.
• Make sure that your listening room is as quiet as possible. For
accurate measurement, turn off air conditioner or other devices
that make noises.
• To achieve the best results possible, vacate your listening room
until the AUTO SETUP procedure is completed so that you may
not obstruct the path of sound beams.
• If there are curtains in your listening room, we recommend
following the procedure below.
1. Open the curtains to improve sound reflection.
2. Run “BEAM OPTIMZ ONLY”.
3. Close the curtains.
4. Run “SOUND OPTIMZ ONLY”.
y
• To return to the previous screen while using SET MENU, press
IRETURN.
1 Press ISETUP.
The remote control keys to be used and available
operations in each step are displayed at the bottom of
the screen.
y
• You can also start the “BEAM+SOUND OPTIMZ”
procedure simply by holding down MINTELLIBEAM for
more than two seconds. In this case, proceed to step 4.
Using AUTO SETUP (IntelliBeam)
(Beam optimization and sound optimization)
Use to optimize the beam angle, delay, volume, and
quality so that the parameters best match your listening
environment. It is recommended that you should select
this optimization feature in the following cases:
• If you make settings for the first time
• If the unit has been relocated
• If your listening room has been restructured
• If the objects in your listening room (furniture, etc.)
have been rearranged
This menu takes about three minutes.
12
34
5
Remove
Fit in
Fit in
Place horizontally
Run through
VOLUME
MIN MAX MIN
MAX
CROSSOVER
HIGH CUT
Subwoofer
(Beam optimization only)
Use to optimize the beam angle so that the parameter
best matches your listening environment.
This menu takes about one minute.
(Sound optimization only)
Use to optimize the beam delay, volume, and quality so
that the parameters best match your listening
environment. You must optimize the beam angle with
“BEAM OPTIMZ ONLY” before starting “SOUND
OPTIMZ ONLY”. It is recommended that you should
select this optimization feature in the following cases:
• If you have opened or closed the curtains in your
listening room before using this unit
• If you have manually set the beam angle.
This menu takes about three minutes.
;MEMORY
;AUTO SETUP
;MANUAL SETUP
;SOUND SET MENU
;SOUND OUT MENU
;INPUT MENU
;DISPLAY MENU
[ ]/[ ]:Up/Down
[ENTER]:Enter
SET MENU
.
p
p
0 +10
ENT
7 8 9
4 5 6
1 2 3
HDMI 4 iPod RADIO
ENTER
SURROUND STEREO
OFF
ENTER
TAINMENT
MUSIC
CINEMA DSP
MOVIE
HDMI 1 HDMI 2 HDMI 3
TV AUX 1 AUX 2
TV AV
MENUTOP MENU
OPTION
TV
MUTE
CODE SET
UNIVOLUME SUR. DECODE INTELLIBEAM
TV
INPUT MUTE
TV VOL CH VOLUME
SETUP RETURN
MEMORY
SLEEPINFO
TUNING PRESET CATEGORY
OPTION SETUP RETURN
I
ENTER
G
M
GENTER
G /
IRETURN
ISETUP
MINTELLIBEAM