Tascam CC-222SL CD Player User Manual


  Open as PDF
of 36
 
1- Introduction
28 TASCAM CC-222SL
6 – After recording
Erasing tracks
It is possible to erase the last recorded track, the last two
recorded tracks, the last three recorded tracks, etc. It is not,
however, possible to erase tracks in the “middle” of the disc.
CAUTION
This operation cannot be undone. If you are going
to erase a track or tracks, make sure that they are
recordings that you really want to erase!
NOTE
To operat this function, the unit should be in Continue
mode. The function cannot to be used when play-
back mode is Single, Random or Program. If erasing
is attempted in such modes, Cannot ERASE! will be
displayed.
1 Withthediscloaded,andtheunitinstopmode,
presstheERASEkey.
2 IfthedisplaydoesnotshowERASEXX-XX?,where
XX-XXisthenumberofthelasttrackrecordedon
thedisc,turntheMULTI DIALorusetheSKIPkeys
untilitisdisplayed.
3 TurntheMULTI DIALorusetheSKIPkeysto
changethenumberofthersttracktobeerased.
Thehighestvaluethatthisnumbercantakeisthe
lasttrackrecorded(forexample,if17trackshave
beenrecordedonthedisc,17-17meansthatthelast
trackonly,number17,willbeerased).Thelowest
valuethatthisnumbercantakeis2(ifthisnumber
was1,thewholediscwouldbeerased,asdescribed
below).Ifyoudonotwanttoproceedwiththeerase
operation,presstheERASEkeyorSTOPkey.
NOTE
If only one track has been recorded on the disc, only
the “erase disc” option (see “Erasing a whole disc” on
page 28) is available.
4 Whentherangeoftrackstobeerasedhasbeen
selected,presstheMULTI DIALortheENTERkey.
If the erase operation has been selected, the word ERASE
flashes on the display, and the timer starts counting down.
At the end of the countdown period, the word Complete
appears briefly on the display, and the display returns to
the track/time display.
Erasing a whole disc
When you want to erase a whole disc (all the tracks on a
disc), follow the procedure below:
1 Withthediscloaded,andtheunitinstopmode,
presstheERASEkey.
2 TurntheMULTI DIALorusetheSKIPkeysuntilthe
displayshowsERASEDISC?.
Ifyoudonotwanttoproceedwiththeeraseopera-
tion,presstheERASEkeyorSTOPkey.
3 Toerasethecontentsofthedisc,presstheMULTI
DIALortheENTERkey.
NOTE
This operation cannot be undone. If you are going to
erase a disc, make sure that it contains only record-
ings that you really want to erase!
Iftheeraseoperationhasbeenselected,theword
ERASEashesonthedisplay,andthetimerstarts
countingdownatimevalueshownonthedisplay.
Attheendofthecountdownperiod,theword
Completeappearsbrieyonthedisplay,andthe
displayreturnstothetrack/timedisplay.
Refreshing a disc
If a CD-RW disc has been corrupted at any point (e.g.
power has been cut off in the middle of a finalize opera-
tion, etc.), or has been used in a computer or another piece
of equipment that makes it unreadable, it is possible to
“refresh” the disc to make it usable again.
1 Withthediscloaded,andtheunitinstopmode,
presstheERASEkey.
2 TurntheMULTI DIALorusetheSKIPkeysuntilthe
displayshowsDISCREFRESH?.
3 Torefreshthedisc,presstheMULTI DIALortheEN-
TERkey.
Ifyoudonotwanttoproceedwiththerefreshop-
eration,presstheERASEkeyorSTOPkey.
NOTE
This operation cannot be undone. If you are going to
refresh a disc, make sure that it contains only record-
ings that you really want to erase!
Iftherefreshoperationhasbeenselected,thewords
ERASEXX:XXareshownonthedisplay,andthe
timerstartscountingdown.
Attheendofthecountdownperiod,thewordCom-
pleteappearsbrieyonthedisplay,andthedisplay
returnstothetrack/timedisplay(ofcourse,there
arenotracks,andthediscisatthestart,withthe
totaltimeofthediscavailableforrecording).
 previous next