Filter
Top Products
16
MZ-R900
4. When all the keys on the set and on the remote commander are
considered as OK, the following displays are shown for 4 sec-
onds.
Example1: When the keys on the set are considered as OK:
Example2: When the keys on the remote commander are con-
sidered as OK:
5. When all keys were checked or if the upper panel is opened,
the key check mode quits and the test mode (display check
mode) comes back.
Key Check Mode
This set can check if the set and remote commander function nor-
mally.
• Setting Method of Key Check Mode
1. Setting the test mode (see page 12).
2. Press the [T MARK] key or [DISPLAY] key on the remote commander
for several seconds (about 3 seconds) activates the key check
mode. (At the last two digits, AD value of remote commander
key line is displayed in hexadecimal)
3. When each key on the set and on remote commander is pressed,
its name is displayed on the remote commander LCD. (The
operated position is displayed for 4 seconds after the slide
switch is operated. If any other key is pressed during this
display, the remote commander LCD switches to its name
display)
Example1: When > key on the set is pressed:
Example2: When
N > key on the remote commander is
pressed:
000 **
Remote commander LCD display
**
: AD value of the remote commander key (hexadecimal
00 to FF)
000 FF **
Remote commander LCD display
**
: AD value of the remote commander key (hexadecimal
00 to FF)
000 rPLAY **
Remote commander LCD display
**
: AD value of the remote commander key (hexadecimal
00 to FF)
888 SET OK **
Remote commander LCD display
**
: AD value of the remote commander key (hexadecimal
00 to FF)
888 RMC OK **
Remote commander LCD display
**
: AD value of the remote commander key (hexadecimal
00 to FF)
Sound Skip Check Result Display Mode
This set can display the count of errors that occurred during the
recording/playing for checking.
• Setting method of sound skip check result display
mode
1. Set the test mode (see page 12).
2. Press the N key or [REC] key, and the playing or recording
sound skip result display mode becomes active respectively
where the LCD displays the following.
3. When the N key is pressed, total error count is displayed on
the LCD, and each time the > key is pressed, the display
item moves down by one as shown below. Also, if the . key
is pressed, the display item moves up by one, then if the [REC]
key is pressed, the display in the record mode appears.
When the [REC] key is pressed, total error count is displayed
on the LCD, and each time the > key is pressed, the display
item moves down by one as shown below. Also, if the . key
is pressed, the display item moves up by one, then if
the N key is pressed, the display in the play mode appears.
• Cause of Sound Skip Error
Cause of error Description of error
EIB Sound error correction error
Play
Stat Decoder status error
Adrs Address access error
BEmp Buffer is empty
BOvr
Buffer is full, and sounds were
dumped
Record
Bful
Buffer capacity becomes less,
and forcible writing occurred
Rtry Retry times over
4. To quit the sound skip check result display mode and to return
to the test mode (display check mode), press the
x key.
000 P**R**
Remote commander LCD display
Total count of play
system errors (hex.)
Total count of record
system errors (hex.)
000 P**R**
000 EIB **
000 Stat**
000 Adrs**
000 BEmp**
000 ######
000 P**R**
000 BOvr**
000 Bful**
000 Rtry**
000 ######
P**R**
: Total play/record errors (hex.)
**
: Counter of sound skip check each item (hex.)
######
: 6-digit address where sound was skipped last (hex.)
Playing sound skip
result display
Recording sound skip
result display