Filter
Top Products
<ARB7050>
9
L
R
PRE
OUT
FRONT
SPEAKERS
SUB WOOFER
AC OUTLETS
CENTER
SPEAKERS
CENTER
SWITCHED
TOTAL 100W MAX
PRE
OUT
UNSWITCHED
100W MAX
SPEAKER IMPEDANCE
8 16 SPEAKER
CAUTION:
THE POWER
SUPPLY CORD SHOULD
BE DISCONNECTED
BEFORE CHANGING
THE VOLTAGE
SELECTOR.
TWO VOLTAGE SELECTORS
110V
120 127V
220V
240V
CAUTION:
DO NOT CONNECT
TV SET CR MONITOR.
220V
110V
120-127V
240V
II
I
REAR
SPEAKERS
I+II
I
ONLY
SEE
INSTRUCTION
MANUAL
SPEAKER
SELECTOR
SPEAKER
IMPEDANCE
8 16
SPEAKER
L
A
R
R
L
B
I+II
I
ONLY
+
+
+
–
–
–
+
–
L
R
PRE
OUT
FRONT
SPEAKERS
SUB WOOFER
AC OUTLETS
CENTER
SPEAKERS
CENTER
SWITCHED
TOTAL 100W MAX
PRE
OUT
UNSWITCHED
100W MAX
SPEAKER IMPEDANCE
8 16 SPEAKER
CAUTION:
THE POWER
SUPPLY CORD SHOULD
BE DISCONNECTED
BEFORE CHANGING
THE VOLTAGE
SELECTOR.
TWO VOLTAGE SELECTORS
110V
120 127V
220V
240V
CAUTION:
DO NOT CONNECT
TV SET CR MONITOR.
220V
110V
120-127V
240V
II
I
REAR
SPEAKERS
I+II
I
ONLY
SEE
INSTRUCTION
MANUAL
SPEAKER
SELECTOR
SPEAKER
IMPEDANCE
8 16
SPEAKER
L
A
R
R
L
B
I+II
I
ONLY
+
–
SP-A(L) SP-A(R)
(L) (R)
FRONT
REAR
+
–
+
+
+
++
+
+
–
–
–
–
–
–
–
+
–
CENTER
CONNECTIONS
SPEAKER SYSTEM CONNECTIONS
NOTE:
Use speakers with an impedance of 8
Ω
to 16
Ω
.
When connecting speakers to the FRONT SPEAKERS B terminals,
the procedure is the same as that used for connecting speakers
to the FRONT SPEAKERS A terminals.
NOTE:
÷
Do not allow any of the cord’s conductors to protrude from the
terminals or touch any other conductors. Malfunctioning or
breakdowns may occur when conductors come into contact
with each other.
÷
If you have one pair of speakers only, connect it to front
speaker terminals A or B.
÷
Be sure to connect single rear speaker to the L channel.
You can set this unit to match the requirements and
specifications of your stereo system’s speakers (whether or
not center speaker(s), rear speakers or a sub-woofer are
used, speaker size, etc.) to assure optimum sound quality.
Before using, perform settings in the SPEAKER MODE (refer
to page 29).
NOTE:
This unit does not feature conventional switching between
NORMAL/WIDE/PHANTOM center modes.
2
1
3
10mm (3/8 in)
2
1
3
+
1 Push the lever forward.
2 Insert the cord into the hole.
3 Pull the lever back.
1 Loosen cap.
2 Insert wire.
3 Tighten cap.
Connecting Two Center Speakers for Dual Center
There are two sets of terminals for center speakers on the main
unit, so you can connect two speakers. When you cannot install
a speaker under or behind your TV, installing speakers either
side of the TV as a center speaker is just as effective.
When the SPEAKER SELECTOR switch is in the “Ι + ΙΙ” position,
be sure to connect two speakers. If only one speaker is connected,
there will be no sound.
Both speaker systems should have an impedance of 4 Ω to 16 Ω.
Speaker cord connection
NOTE:
Before connecting pin jacks, speaker cables and other jacks and cables, switch power to the unit
OFF, and wait for about one hour. (When power is ON, the rear panel may become very hot.)
SPEAKER
SELECTOR
SPEAKER
SELECTOR
Illustration shows
Multi-voltage model.
Illustration
shows Multi-
voltage model.