Filter
Top Products
<ARB7050>
10
CONNECTIONS
IR REPEATER CONNECTION
Connecting a supplied IR Repeater lets you also control other components with this unit’s remote control.
NOTE:
To operate components not made by Pioneer, perform REMOTE SET UP (page 31) after connecting an IR Repeater.
Remote control signals directed towards this unit or GUI operation signals are transmitted from the repeater as infrared signals, enabling
control of other components.
There are two kinds of infrared repeaters. Connect either or both to match the remote control requirements of different components.
MAIN-REPEATER
Use this to operate other components with this unit’s remote
control or to operate using GUI on-screen indications.
Install on top of this unit as shown in the figure.
MAIN-REPEATER
1 Insert the REPEATER’s two
pegs into the holes on the top.
2 Install the REPEATER laying
on its side on the top.
The pegs are usually
inserted in the two
rear holes.
Use the two front holes when
there’s another component on
top of this preventing easy
reception of the MAIN
REPEATER’s infrared signals.
CD
VCR
MINI-REPEATER
Use this when a component operates incorrectly after receiving
a signal from this unit’s remote control, or when it is difficult for
a component to receive signals from the Main-Repeater. Stick it
directly on the remote control sensor window.
There are two MINI-REPEATER terminals.
If you need another Mini-Repeater, contact you nearest Pioneer
Service Center.
VCR
MINI-REPEATER
NOTE:
Before connecting the MAIN-REPEATER or MINI-REPEATER, switch power to the unit OFF, and wait
for about one hour. (When power is ON, the rear panel may become very hot.)
Illustration shows Multi-voltage model.
PHONO
TAPE2
MONI-
TOR
CD
LD
TAPE1
IN
OUT
TO MONITOR TV
VIDEO OUT
CONTROL
IN
OUT
IN
GND
L
R
REC
PLAY
PLAY
REC
IN
IN
OUT
IN
VCR2
VCR1
TV
/SAT
SEE INSTRUCTION MANUAL
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.
"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF
DOLBY LABORATORIES LICENSING CORPORATION.
MINI-
REPEATER
MAIN-
REPEATER
1
2
L
R
VIDEO
ANTENNA
FM
BAL
300
FM
UNBAL
75
GND
AM
LOOP
ANTENA
IN
SYSTEM CONTROL
IR OUT
PAL
NTSC
FM 50kHz
/50S
AM 9kHz
CHANNEL
/FM DE-
100kHz
/75S
10kHz
STEP
EMPHASIS
S
OUT
S
IN
S
IN
S
OUT
TO
MONITOR
TV
VCR
1
2
1 Remove the seal.
2 Stick onto the remote control
sensor window.
Illustration shows Multi-voltage model.
PHONO
TAPE2
MONI-
TOR
CD
LD
TAPE1
IN
OUT
TO MONITOR TV
VIDEO OUT
CONTROL
IN
OUT
IN
GND
L
R
REC
PLAY
PLAY
REC
IN
IN
OUT
IN
VCR2
VCR1
TV
/SAT
SEE INSTRUCTION MANUAL
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.
"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF
DOLBY LABORATORIES LICENSING CORPORATION.
MINI-
REPEATER
MAIN-
REPEATER
1
2
L
R
VIDEO
ANTENNA
FM
BAL
300
FM
UNBAL
75
GND
AM
LOOP
ANTENA
IN
SYSTEM CONTROL
IR OUT
PAL
NTSC
FM 50kHz
/50S
AM 9kHz
CHANNEL
/FM DE-
100kHz
/75S
10kHz
STEP
EMPHASIS
S
OUT
S
IN
S
IN
S
OUT
TO
MONITOR
TV
1
2
VSX-D3S
VSX-D3S
NOTE:
To prevent possible damage, be careful to avoid accidentally
connecting the MINI-REPEATER to the MAIN-REPEATER
terminals.