Filter
Top Products
<ARB7050>
11
L
R
PHONO
TAPE2
MONI-
TOR
CD
LD
TAPE1
IN
OUT
TO MONITOR TV
VIDEO OUT
CONTROL
IN
OUT
IN
PRE
OUT
FRONT
SPEAKERS
SUB WOOFER
AC OUTLETS
CENTER
SPEAKERS
CENTER
SWITCHED
TOTAL 100W MAX
GND
L
R
REC
PLAY
PRE
OUT
PLAY
REC
IN
IN
OUT
IN
VCR2
VCR1
TV
/SAT
SEE INSTRUCTION MANUAL
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.
"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF
DOLBY LABORATORIES LICENSING CORPORATION.
MINI-
REPEATER
MAIN-
REPEATER
1
2
L
R
VIDEO
ANTENNA
UNSWITCHED
100W MAX
SPEAKER IMPEDANCE
8 16 SPEAKER
FM
BAL
300
FM
UNBAL
75
GND
AM
LOOP
ANTENA
IN
SYSTEM CONTROL
IR OUT
CAUTION:
THE POWER
SUPPLY CORD SHOULD
BE DISCONNECTED
BEFORE CHANGING
THE VOLTAGE
SELECTOR.
TWO VOLTAGE SELECTORS
110V
120 127V
220V
240V
CAUTION:
DO NOT CONNECT
TV SET CR MONITOR.
220V
110V
120-127V
240V
PAL
NTSC
FM 50kHz
/50 S
AM 9kHz
CHANNEL
/FM DE-
100kHz
/75 S
10kHz
STEP
EMPHASIS
SPEAKER
IMPEDANCE
8 16
SPEAKER
S
OUT
S
IN
S
IN
S
OUT
TO
MONITOR
TV
II
I
REAR
SPEAKERS
I+II
I
ONLY
SEE
INSTRUCTION
MANUAL
SPEAKER
SELECTOR
SPEAKER
IMPEDANCE
8 16
SPEAKER
L
A
R
R
L
B
TV
/SAT
LD
AC-3 •
DIGITAL IN
AC-3 •
RF IN
1 2 3 4
5
7 8 9
10 11 12 13
6
14 16 17 18 20 21 23 24 25 26 2715 19 22
REAR PANEL FACILITIES
Illustration shows Multi-voltage model.
1 FM/AM ANTENNA terminals
Use these antenna terminals for reception of normal FM and AM
broadcasts.
2 CHANNEL STEP switch
(Multi-voltage model only)
See page 4.
3 PAL/NTSC switch
(Multi-voltage model only)
See page 4.
4 TAPE 2 MONITOR jacks
Connect to audio components such as a second cassette deck or
a graphic equalizer.
5 PHONO input jacks
Connect to the output cables from a turntable.
6 GND terminal
Connect the turntable ground lead to this terminal.
7 VCR 2 jacks
[VIDEO OUT]
Connect to the VCR 2 VIDEO INPUT jack.
[AUDIO OUT (L, R)]
Connect to the VCR 2 AUDIO INPUT jacks.
[VIDEO IN]
Connect to the VCR 2 VIDEO OUTPUT jack.
[AUDIO IN (L, R)]
Connect to the VCR 2 AUDIO OUTPUT jacks.
8 VIDEO OUT (TO MONITOR TV) jack
Connect to a monitor TV or to TV sets with video input terminals
to watch program materials from a VCR or LD player connected
to this unit.
9 CONTROL IN/OUT jacks
IN : Connect this jack to other Pioneer components when
using those components to control this unit.
OUT : Connect this jack to other Pioneer components when
using the remote control of this unit to control the other
components.
NOTE:
÷
If there is a plug in this unit’s CONTROL IN jack, Intelligent
System Control and GUI operation are not possible.
÷
The receiver’s remote sensor does not function when a plug is
inserted in the IN jack. To operate, point a remote control unit
other than this unit's supplied remote control unit at the
remote sensor on the component to which the receiver’s IN
jack is connected.
÷
You cannot use the supplied remote control unit to operate this
unit via another component’s remote sensor.
To the CONTROL IN jack of
the PIONEER component
bearing the Î mark.
PIONEER component
bearing the Î mark.
Remote
control unit
0 SYSTEM CONTROL IR OUT jacks
To operate other components with this unit’s remote control or
with GUI, connect the supplied repeater. (See page 10.)
MINI-REPEATER 1, 2:
Connect the supplied Mini-Repeater.
MAIN-REPEATER:
Connect the supplied Main-Repeater.
- SUB WOOFER PRE OUT jack
When you play back the low frequencies with a sub-woofer,
connect to a powered sub-woofer.
= CENTER PRE OUT jack
Connect when using a PIONEER projection monitor receiver's
built-in speaker as a center speaker.
Refer to the projection monitor's operating instructions for details
concerning connection and operation.
Receiver