Filter
Top Products
45
Speaker Setup
1-3. Level Calibration Sub-menu
Use this sub-menu to set the volume for each speaker so that each
volume is heard by the listener at the same level. This is especially
important for speaker layouts where the left and right speakers are at
different distances or in asymmetrical positions due to room designs
and configurations. These settings and the distance settings
performed in the Speaker Distance Sub-menu are vital to create the
proper sound space and dynamics.
Note:
The speaker level settings here are not effective for multi-channel
input sources. To adjust the speaker levels for multi-channel input
sources, you will need to use the CH SEL, LEVEL
, and LEVEL
buttons on the RC-510M remote controller. See page 33.
Calibrating the speaker levels
(1) When this sub-menu is entered, the TX-SR800 will emit a pink
noise from the front left speaker. At this time, the volume of the
pink noise will automatically increase to a predetermined
reference level (0dB). Remember the volume level of this noise
and then press the
cursor button. (Note that this can be
adjusted to any level between –12 and 12 decibels in 1-decibel
increments.) The TX-SR800 will now emit the pink noise from
the center speaker.
(2) Using the
and cursor buttons, adjust the volume level of the
noise from the center speaker so that it is at the same level as that
was emitted from the front left speaker. You can jog back and
forth between the speakers to help you compare the volume
levels.
(3) Press the
cursor button again. The TX-SR800 will now emit
the pink noise from the front right speaker.
(4) Repeat steps (2) and (3) above for the front right and other
speakers until all speakers are adjusted to the same volume level.
Notes:
• Speakers that you selected “No” or “None” for in the Speaker
Config Sub-menu will not appear.
• To accurately set the output levels, it is recommended to use a
handheld sound pressure level (SPL) meter. Set the meter to C-
weighting and slow averaging. A Radio Shack
®
SPL meter or
equivalent is recommended. Using the internal channel noise
generators, set each channel so that you read a 75 decibel sound
pressure level.
a. Left
Sound comes from the front left speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel increments.
b. Center
Sound comes from the center speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel increments.
c. Right
Sound comes from the front right speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel increments.
d. Surr Right
Sound comes from the surround right speaker. Adjust the sound
level between –12 and 12 decibels in 1-decibel increments.
e. Surr Back R
Sound comes from the surround back right speaker. Adjust the sound
level between –12 and 12 decibels in 1-decibel increments.
f. Surr Back L
Sound comes from the surround back left speaker. Adjust the sound
level between –12 and 12 decibels in 1-decibel increments.
Note:
If the Surr Back/Zone 2 setting in the Surr Back/Zone 2 Sub-menu of
the Hardware Setup Menu is set to “Zone 2,” then the Surr Bk R and
Surr Bk L settings will not be displayed.
g. Surr Left
Sound comes from the surround left speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel increments.
h. Subwoofer
Sound comes from the subwoofer. Adjust the sound level between
–15 and 12 decibels in 1-decibel increments.
Using the remote controller
1. Press the TEST button.
You will hear a pink noise will be emitted
from the front left speaker.
(1) Remember the volume level of this noise and then press the CH
SEL button. The TX-SR800 will now emit the pink noise from
the center speaker.
(2) Using the LEVEL
/ buttons, adjust the volume level of the
noise from the center speaker so that it is at the same level as that
that was emitted from the front left speaker.
(3) Press the CH SEL button again. The TX-SR800 will now emit
the pink noise from the front right speaker.
Use the LEVEL
/ buttons to adjust the volume of the noise
from the front left speaker so that it is the same level as that that
was emitted from the center speaker. The pink noise level can be
adjusted in 1-dicibel increments.
(4) Use the CH SEL button to select other speakers and adjust the
volumes until all speakers are adjusted to the same level.
2. Press the TEST button to complete
the procedure.
Advanced Menu
1.Speaker Setup
1-3.Level Calibration
a.Left : 0dB
b.Center : 0dB
c.Right : 0dB
d.Surr Right : 0dB
e.Surr Back R : 0dB
f.Surr Back L : 0dB
g.Surr Left : 0dB
h.Subwoofer : 0dB
Quit:|SETUP|