Onkyo HT-R640 Stereo Receiver User Manual


 
76
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you cant resolve the issue
yourself, contact your Onkyo dealer.
Cant turn on the AV receiver
Make sure that the power cord is properly plugged
into the wall outlet.
Unplug the power cord from the wall outlet, wait ve
seconds or more, then plug it in again.
The AV receiver turns off as soon as its turned
on
The amp protection circuit has been activated.
Remove the power cord from the wall outlet immedi-
ately and contact your Onkyo dealer.
Theres no sound, or its very quiet
Make sure that the digital input source is selected
properly (page 39). Press the [DIGITAL INPUT] but-
ton repeatedly
Make sure that all audio connecting plugs are pushed
in all the way (page 18).
Make sure that the inputs and outputs of all compo-
nents are connected properly (page 18).
Make sure that the polarity of the speaker cables is
correct, and that the bare wires are in contact with the
metal part of each speaker terminal (page 20).
Make sure that the input source is properly selected
(page 45).
Make sure that the speaker cables are not shorting.
Check the volume. It can be set to MIN, 1 through 99,
or MAX (page 45). The AV receiver is designed for
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
If the MUTING indicator is shown on the display,
press the remote controllers [MUTING] button to
unmute the AV receiver (page 47).
While a pair of headphones is connected to the
PHONES jack, no sound is output by the speakers
(page 47).
If theres no sound from a DVD player connected to an
HDMI IN, check the DVD players output settings,
and be sure to select a supported audio format.
Check the digital audio output setting on the con-
nected device. On some game consoles, such as those
that support DVD, the default setting is off.
With some DVD-Video discs, you need to select an
audio output format from a menu.
If your turntable doesnt have a built-in phono
preamp, you must connect one between it and the AV
receiver. If your turntable uses an MC cartridge, you
must connect an MC head amp, or an MC transformer
and phono equalizer.
Make sure that none of the connecting cables are bent,
twisted, or damaged.
Not all listening modes use all speakers (page 59).
Specify the speaker distances (page 63) and adjust the
individual speaker levels (page 64).
Make sure that the speaker setup microphone is not
still connected.
The input signal format is set to PCM or DTS. Set it to
Auto (page 70).
Only the center speaker produces sound
If you use the Pro Logic II Movie, Pro Logic II Music,
or Pro Logic II Game listening mode with a mono
source, such as an AM radio station or mono TV pro-
gram, the sound is concentrated in the center speaker.
Make sure the speakers are congured correctly
(page 42).
The surround speakers produce no sound
When the Stereo or Mono listening mode is selected,
the surround speakers produce no sound (page 59).
Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
Make sure the speakers are congured correctly
(page 42).
The center speaker produces no sound
When the Mono or Stereo listening mode is selected,
the center speaker produces no sound (page 59).
Make sure the speakers are congured correctly
(page 42).
Power
Audio
If you cant resolve the issue yourself, try resetting
the AV receiver before contacting your Onkyo
dealer.
To reset the AV receiver to its factory defaults,
turn it on and, while holding down the [VIDEO 1]
button, press the [STANDBY/ON] button. Clear
will appear on the display and the AV receiver will
enter Standby mode.
Note that resetting the AV receiver will delete your
radio presets and custom settings.
STANDBY/ON
VIDEO 1
VCR 1