Filter
Top Products
19
ANALOG
PR ΙΙ
SUBWFRLFE
VOL
AUTO SR
INPUT ATT
DSP
LCR
LS S RS
LPCM
DOLBY D
DTS
Basic Settings
R
ΙΙ
VOL
SR
ATT
2
Press CONTROL ∞ (or 5) repeatedly until
“MODE” (with the current setting)
* appears on
the display.
* “MANUAL” is the initial setting. If you have already changed
the setting, another mode will be shown.
3
Press CONTROL 3 (or 2) to select “AUTO1” or
“AUTO2.”
• Each time you press the button, Auto Function mode changes
as follows:
AUTO1 : When a video component is turned on while the
unit is on, the unit selects the video component as
the source automatically.
The AUTO MODE indicator lights up on the
display.
AUTO2 : • When a video component is turned on
–while the unit is off, the unit changes the mode
into TV Direct and selects the video component
as the source automatically.
–while the unit is on or TV Direct is activated,
the unit selects the video component as the
source automatically.
• When a video component is turned off
–while TV Direct is activated or the unit is on
with one of the video components selected,
the unit selects the previously selected video
component as the source automatically. (If all
the video components are turned off, the unit
will be turned off automatically.)
The AUTO MODE indicator lights up on the
display.
MANUAL : Select the source manually.
Notes:
• When selecting VCR as the source, “AUTO1” or “AUTO2” may not
work if you only turn on the VCR. If it happens, you may need to
start playback to activate Auto Function mode.
• When video components are selected at the same time, DVD is
selected rather than STB and VCR, and STB is selected rather than
VCR.
ON : The AUTO SR indicator lights up on the display.
•If multichannel signals come in, an appropriate
Surround mode will be turned on.
•If Dolby Digital 2ch or DTS 2ch signals including
surround signals come in, “PL II MOVIE” will be
selected.
•If Dolby Digital 2ch or DTS 2ch signals not
including surround signals come in, “STEREO”
will be selected.
•If Linear PCM signals come in, nothing will
change.
OFF : Select this to deactivate Auto Surround.
Notes:
• This function does not take effect in the following cases:
– While playing an analogue source.
– While selecting “DGTL D.D.” or “DGTL DTS” as the fixed digital
input mode (see pages 13 and 14).
• If Surround mode is automatically activated by Auto Surround,
another Surround mode in use will be canceled temporarily. When
multichannel digital signals stop coming in, the selected Surround
mode is canceled, and the previous Surround mode resumes.
• If you press SURROUND ON/OFF or SURROUND MODE with
Auto Surround activated, Auto Surround will be canceled
temporarily for the currently selected source.
Auto Surround setting will be restored in the following cases:
– When you turn off and on the unit,
– When you change the source,
– When you change the analogue/digital input, and
– When you reset “AUTO SR” to “ON” again.
To cancel Auto Surround
Repeat steps
1
and
2
, then select “OFF” in step
3
.
Setting the Auto Function Mode
You can activate Auto Function mode.
• This function takes effect only when the video components and
TV are connected to this unit with SCART cables.
• This function takes effect for the following sources—DVD, STB,
and VCR.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1
again.
1
Press SETTING.
The CONTROL buttons now work for basic
settings.
CONTROL
CONTROL
SETTING
EN10-19.RX-E111&112RSL[B]_f 02.1.17, 9:19 AM19