Integra DTR-7.3 Stereo Receiver User Manual


 
51
Input Setup
Input source signals
a. Analog/PCM
Analog sources consist of LP records, FM and AM broadcasts,
cassette tapes, and the such. PCM (Pulse Code Modulation) is one
form of digital audio signals and is recorded directly onto compact
discs and DVDs without compression.
b. PCM fs=96k
Digital PCM sources recorded with a sampling rate of 96 kHz.
c. Dolby D (Dolby Digital)
Dolby Digital is compressed digital data with a maximum 5.1-
channel surround output. This source signal comes from DVDs and
LDs that have the
mark and therefore recorded for 5.1-channel
output. This source also comes from digital satellite broadcasts that
support Dolby Digital.
Dialog norm
Dialogue Normalization (Dialog Norm) is feature of Dolby
Digital. When playing back software that has been encoded in
Dolby Digital, sometimes you may see a brief message in the
front panel display that reads Dialog Norm xdB (x being a
numeric value). Dialogue Normalization serves to let you know
if the source material has been recorded at a higher or lower level
than usual. This data is automatically used by the Dolby Digital
decoder to adjust the output volume of the source material
without affecting the volume of your amplifier. Therefore, even
if source material volume changes, you will not have to adjust
the volume on your amplifier.
d. DTS
DTS (Digital Theater System) is compressed digital data with a
maximum 5.1-channel surround output (6.1-channel with DTS-ES
Discrete sources) that allows for an extremely high-quality sound.
This source signal requires a DVD player that supports DTS output
and comes from DVDs, compact discs, and LDs that have the
mark.
e. D.F. 2 ch (Digital Format 2 channel)
2-channel digital signals (not including PCM) such as Dolby Digital.
DVDs or LDs recorded with 2-channel sound may be this type of
input signal.
f. D.F. Mono (Digital Format Monaural)
Monaural digital signals (not including PCM) such as Dolby Digital.
DVDs or LDs recorded with monaural sound may be this type of
input signal.
Listening Modes
Mono
This mode is for playing old movies where the sound is recorded in
monaural or for playing the left and right channels of movies
separately that contain different language signals. This mode also
allows you to listen to the multiplexed soundtracks on DVDs, and
other media that have them.
Direct
This mode delivers pure sound with minimum sound quality
adjustment and filtration. The sound recorded for the right and left
front channels is output to the right and left front speakers only and
not output to the subwoofer.
Pure Audio
Same as the direct mode except that the pure audio mode also turns
off the display window, turns off the power supply to the video
circuitry, and minimizes the sources of noise. The result is high-
fidelity music playback true to the original source.
Note that if you connect a device to the COMPONENT VIDEO
INPUT 2 jacks of the DTR-7.3, the relay switch doesnt activate and
signals are output to the COMPONENT VIDEO OUTPUT jacks.
Therefore, the display on the monitor connected to the
COMPONENT VIDEO OUTPUT jacks will not disappear.
Stereo
This mode has all input sound is output from the left and right front
speakers.
The subwoofer is also used for playback.
T-D (Theater-Dimensional)
For the best enjoyment of your home theater, it is recommended that
you have front left and right speakers, a center speaker, and surround
left and right speakers. However, if you only have front left and right
speakers, you can enjoy multichannel audio by using this mode.
This mode controls the characteristics of the sound that reaches each
ear to reproduce a multi-speaker setup. To receive the full effect,
there is an optimum listening position (sweet spot). Refer to the
explanation of the listening angle (see page 55). In addition, if the
reflective sound components are large, it may be difficult to achieve
the desired result, so be sure to set up your system and listening
position to minimize reflective sound.
Dolby Pro Logic II
Opposed to Dolby Pro Logic, which had four channels (front, left,
center, and surround) recorded into two channels with matrix
processing and then played back in four channels, Dolby Pro Logic
II uses a feedback logic circuit to have 5.1-channel surround audio
(Dolby Surround, etc.) matrix-encoded into two channels and then
played back in its original 5.1-channel form.
Dolby Pro Logic II provides a Movie mode designed for playing
movies and a Music mode designed for listening to music. In the
Movie mode, the surround channels, which used to provide
monaural output over only a narrow frequency range, now provide
complete stereo output over the full frequency range. The result is
movie viewing with a realistic feel of movement. The Music mode
uses the surround channels to provide a natural soundfield that
cannot be provided with normal stereo output.
This mode can be used with VHS and DVD videos with the
mark and certain television programs. The Music mode
can be used with music compact discs and other stereo sources.
Dolby D (Dolby Digital)
This mode is used for playing Dolby Digital sources.
Dolby Digital EX
Enabled when playing back sources with surround tracks that
were encoded using the Surround EX technology.
Dolby EX
Select to achieve the same effects as Dolby Digital EX encoded
sources with non-Dolby Digital sources.