Filter
Top Products
MAIN REMOTE CONTROL FUNCTIONS
c
Memory Button: Press this button to enter a
radio station to the AVR 430’s preset memory. First,
tune the desired station, and then press this button.
Within five seconds of when you see the station’s
frequency flash in the
Upper Display Line # and
in the on-screen display, press the numeric keys
for the preset number between 01 and 30 that you
wish to assign to the station. (See page 33 for more
information.)
d
Stereo Mode Select Button: Press this button
to select a stereo listening mode. When the button is
pressed so that
SURROUND OFF appears in
the
Lower Display Line $, the AVR will operate in
either a bypass mode with true, fully analog, two-
channel left/right stereo mode with no surround pro-
cessing or with full bass management, as opposed to
other modes where digital processing is always used.
When the button is pressed so that
SURROUND
OFF
appears in the Lower
Display Line $, and
the
DSP and SURROUND
OFF Surround
Mode Indicators
% are lit, you will enjoy a two-
channel presentation of the sound along with the ben-
efits of bass management. Depending on whether
your system is configured for 5.1 or 6.1/7.1 chan-
nels, the next press of the button will cause either
5CHSTEREO or 7CHSTEREO to
appear, and the stereo signal will be routed to all five
(or seven) speakers. (See page 31 for more informa-
tion on stereo playback modes.)
e
DTS Neo:6 Mode Select Button: Press this
button to select a DTS Neo:6 mode. (See page 31
for the available DTS Neo:6 options.)
f
DTS Digital Mode Select Button: When a
DTS-encoded digital source is playing, each press of
this button will scroll through the available DTS modes.
The specific choice of modes will vary according to
the type of encoding on the disc and your system’s
speaker configuration. When a DTS source is not in
use, this button has no function. (See page 31 for the
available DTS digital options.)
g
Dolby Mode Select Button: This button is used
to select from the available Dolby Surround modes.
Each press of this button will select
one of the Dolby
Pro Logic II modes or Dolby 3 Stereo.
When a Dolby
Digital-encoded source is in use, the Dolby Digital
mode may also be selected. (See page 31 for the
available Dolby surround mode options.)
h
6-Channel/8-Channel Input Select: Press this
button to select the device connected to the
6- or 8-
Channel Direct Inputs
. (See page 29 for more
information.)
i
SPL Select Button: This button activates the
EzSet function to quickly and accurately calibrate the
AVR 430’s output levels. When the button is pressed
you will then need to select between automatic EzSet
operation or using the remote as a manual SPL meter
by pressing the
⁄
/
¤
Navigation Button o until
your choice appears in the remote’s LCD display.
Press the
Set Button q to enter the setting, and
then follow the instructions as displayed in the LCD
display. (For complete information, see page 26.)
j
EzSet Microphone Sensor: The microphone
sensor that is used by the EzSet system is behind the
three slots at the top of the remote control. When
using EzSet to calibrate the AVR 430, be certain that
the slots are not covered. (See page 26 for more
information on using EzSet.)
k
Lens: The infrared emitters behind the plastic
lens at the top of the remote communicate the remote
codes to the AVR 430. Be certain that the lens is not
covered when using the remote, and point the lens
toward the AVR for best results. In learning mode, the
remote receives IR codes to be learned through a
sensor behind the lens.
NOTE: DO NOT remove the rubber plug that is supplied
to cover the jack on the upper right side of the remote.
The jack is not active and is reserved for future use.
40
14 MAIN REMOTE CONTROL FUNCTIONS