Filter
Top Products
Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting
h Trigger Out 1
Select the conditions to turn on the trigger out 1 with respect to
the zone, input source, surround mode, HDMI monitor, etc.
For details about the trigger out function, see page 24.
j Trigger Out 2
This sets the conditions to turn on the trigger out 2, in the same
way as “Trigger Out 1” above.
k Trigger Out 3
This sets the conditions to turn on the trigger out 3, in the same
way as “Trigger Out 1” above.
l Trigger Out 4
This sets the conditions to turn on the trigger out 4, in the same
way as “Trigger Out 1” above.
[Selectable items]
ON
– – –
Setting with Respect to the Zone
When the power of the zone turned on/off, the trigger out turns on.
Setting with Respect to the Input Source
When the input source set to on is selected, the trigger out turns on.
Setup
Associated with respect to the input source for zones set to “ON” at
“Setting with Respect to the Zone”.
A0 Transducer Setup
Settings when using transducer.
A2 Remote ID
Set remote control ID.
Match the ID setting of the remote control unit and the receiver.
• When changing the remote ID, also change the AMP, iPod, TU and
NET/DTU modes of the main remote control unit at the same time
(vpage 79).
• When changing the remote ID, also change the sub remote control
unit at the same time (vpage 84).
A1 Digital Out
Set usage of OPT4 OUT.
NOTE
The ZONE4 operations cannot be performed when set to “Rec
Select”.
[Selectable items]
ZONE4 Select
Rec Select
[Selectable items]
1
2
3
4
The Transducer Setup can be accessed through GUI menu “Speaker
Setup” – “Subwoofer Setup” is “1SP”, “2SP L/R” or “2SP MIX”. The
transducer signal is outputted from “SW3”.
Setting with Respect to the Surround Mode
When the surround mode set to on is selected, the trigger out turns
on.
Setting with Respect to the Monitor
When the HDMI monitor set to on is selected, the trigger out turns
on.
Level
[Variable range]
–12dB
~
0dB
~
+12dB
:
Set the transducer level.
OFF
:
Turn the transducer output off.
LPF
Set the upper limit for the bass signal frequency outputted from the
transducer.
[Selectable items]
40Hz
60Hz
80Hz
90Hz
100Hz
110Hz
120Hz
150Hz
200Hz
250Hz
This is effective when the “MAIN ZONE” has been set to “ON” for
the “Setting with Respect to the Zone” and the input source which is
set to “ON” has been selected for the “Setting with Respect to the
Input Source”.
This is effective when the “MAIN ZONE” has been set to “ON” for
the “Setting with Respect to the Zone” and the input source which is
set to “ON” has been selected for the “Setting with Respect to the
Input Source”.
When you adjust “Level”, the adjusted value is set for all surround
modes. To adjust the level for individual surround modes, use “Channel
Level” (vpage 74).
A3 2Way Remote
Set when using the 2-way remote control unit.
When using a 2-way remote control unit (RC-7000CI and RC-7001RCI,
sold separately), set this to “Used”.
[Selectable items]
Used
Not Used
NOTE
• When using the 2-way remote control unit, connect to the Port 1 RS-
232C connector.
• If GUI menu “Manual Setup” - “Option Setup” - “2Way Remote”is
set to “Used”, you cannot use port 1 of the RS-232C terminal for the
external controller.
AVR5308CIEU_100_初校作成中.indd 41 2008/05/26 9:40:54