Filter
Top Products
–
17
–
EN
English
Getting started
•Turn on the power of the TV, amplifier and any other com-
ponents which are connected to the DVD player.
• Make sure the TV and audio receiver (commercially avail-
able) are set to the correct channel.
Press the POWER ON button.
• “P-ON” will appear briefly on the display panel.
Press the OPEN/CLOSE button
to open disc loading tray.
Place the disc in the tray, with the
label facing up.
Press the PLAY button.
• The tray will close automatically,
then playback will start from the first
chapter or track of the disc. If the playback does not
start automatically, press the PLAY button.
• When you play back the DVD with a title menu, it may
appear on the screen. In this case, refer to “Title menu”
on page 18.
Press the STOP button to stop playback.
NOTES:
•A “prohibited icon” may appear at the top-right
corner on the TV screen during operation,
warning that a prohibited operation has been
encountered by the DVD player or the disc.
• With DVDs that use some titles for playback
program signals, playback may start from the second title,
or it may skip these titles.
• During the playback of two layered disc, pictures may stop
for a moment.This happens when the 1st layer switches to
the 2nd layer. This is not a malfunction.
• The operation may vary when you play back DVDs with
disc menu or DivX
®
video files. Refer to the manual accom-
panying the disc for details.
5
4
3
2
1
DivX
®
WMAJPEG
MP3
Super
Audio CD
CDDVD-ADVD-V
DISC PLAYBACK
Basic Playback
DVD and DivX
®
video file may contain menus to navigate
the disc and access special features. Press the appropri-
ate Numeric buttons or use the Cursor buttons (K / L /
s / B) to highlight your selection in the DVD main menu
and press the ENTER button to confirm.
NOTES:
• Unless otherwise stated, all operations described in this
manual are based on remote control use. Some operations
can be carried out using the menu bar on the TV screen.
• The Numeric buttons are invalid in menu of DivX
®
video
file.
DivX
®
DVD-ADVD-V
General Features
HDMI Setup
Press the HDMI button on the front panel to select
the HDMI output mode.
The output mode changes as follows every time
the HDMI button is pressed.
• The HDMI indicator on the front panel lights up when
HDMI output mode is on.
480P/576P (Default):
Video output from the HDMI OUT jack at 480p/576p.
720P: Video output from the HDMI OUT jack at 720p.
1080: Video output from the HDMI OUT jack at 1080i.
1080P: Video output from the HDMI OUT jack at 1080p.
OFF: No video output from the HDMI OUT connector.
NOTES:
• Video and audio signals may distorted temporarily when
switching to/from the HDMI output mode.
•
Use a display equipment with an HDMI-compatible port.
•
The HDMI indicator on the front panel flashes when you
select the HDMI output mode but there is no HDMI cable.
• If you turn on the pure direct mode, both video and audio
signals thru the HDMI output will be cut off (press the
PURE DIRECT button again to recover).
•You can check the HDMI connection status by pressing the
DISPLAY button during playback with the HDMI output
mode (refer to page 25).
• If the TV is not compatible with newly selected HDMI output
mode, the actual output mode will be kept the one before
changing the selection.When this occurs, the newly select-
ed mode will appear on the front panel display (see page
11) while the actual output resolution will be indicated by
performing the on-screen display as described in NOTE
OFR HDMI DISPLAY on page 25.
• Actual output signals for each HDMI mode vary with DVD
the compatibility of the connected display device.
• You cannot select the HDMI output mode when the setup
menu is on the TV screen.
1
1080 1080P OFF480P/576P
720P
Pure Direct Mode
Press the PURE DIRECT button on the front panel to
output an analog audio signal only (no analog video
and HDMI signals will be output and the display will be
turned off). The higher quality sound will be achieved.
NOTES:
• When the buttons below are pressed, the pure direct mode
will be released.
OPEN/CLOSE button (on both the remote and the front panel),
SETUP or DISPLAY button (on the remote), ON/STANDBY or
PURE DIRECT button (on the front panel).
• The PURE DIRECT button will not function while displaying
the setup menu.
• If you turn on the pure direct mode while selecting HDMI
mode, both video and audio signals will not be output.
1
Press the DIMMER NTSC/PAL button on the front
panel to select the desired brightness of the front
panel display. (BRIGHT, DIMMER or OFF)
• The default setting is BRIGHT.
NOTES:
• The brightness of the front panel display can be adjusted
from the setup menu. Details are on page 31.
• When you turn on the power next time, the brightness of
the front panel display will be as set in setup menu.
1
Select a suitable video system according to the format
of the TV you connected.
Stop playback.
Press the DIMMER NTSC/PAL button on the front
panel more than 3 seconds. The video system will be
displayed on the front panel display and TV screen.
Press the DIMMER NTSC/PAL button on the front
panel more than 3 seconds. The video system will
be displayed on the front panel display and TV
screen.
• If it is left untouched for more than 5 seconds or any
other buttons are pressed, the unit will switch back to
the normal status.
NOTES:
• If the video system setting does not fit to the TV you con-
nected, the picture will be distorted.
• If you turn off the unit, the video system will go back to the
one set for the TV TYPE on the display menu (refer to
page 28).
3
2
1
Brightness of the Front Panel Display
TV TYPE
NTSC PALMULTI
NTSC PALMULTI
E6EE0UD(EN).qx4 07.5.15 9:44 AM Page 17