41
Basic Operations of the Function Menu
Chapter 3 Preparations
P3 AUDIO page
P4 TC page
F2: A2 INPUT Selects the audio input signal to assign
to audio channel 2.
SDI
: Audio signal embedded into SDI
signal
ANALOG2: Analog 2 audio signal
AES/EBU: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 1/2 connectors
F3: MONITR L Selects the channel to monitor as the left
monitor channel.
CH1
, CH2, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F4: MONITR R Selects the channel to monitor as the
right monitor channel.
CH1
, CH2, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F5: SPEAKER Enables or disables output from this
unit’s speaker.
OFF
: Do not output
ON: Output
F6: LEVEL MT Specifies the position at which to
superimpose audio level meters in the
video monitor screen (in full-screen
display mode).
OFF
: Do not superimpose.
LEFT: Superimpose the audio level
meters of 2 channels on the left side.
RIGHT: Superimpose the audio level
meters of 2 channels on the right
side.
LEFT(4): Superimpose the audio level
meters of 4 channels on the left side.
RIGHT(4): Superimpose the audio level
meters of 4 channels on the right
side.
LEFT(8): Superimpose the audio level
meters of 8 channels on the left side.
RIGHT(8): Superimpose the audio level
meters of 8 channels on the right
side.
Item Setting
F1: A3 INPUT Selects the audio input signal to assign
to audio channel 3.
SDI
: Audio signal embedded into SDI
signal
ANALOG1: Analog 1 audio signal
AES/EBU: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 3/4 connectors
F2: A4 INPUT Selects the audio input signal to assign
to audio channel 4.
SDI
: Audio signal embedded into SDI
signal
ANALOG2: Analog 2 audio signal
AES/EBU: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 3/4 connectors
F3: (Unassigned function button)
F4: (Unassigned function button)
Item Setting
F5: (Unassigned function button)
F6: (Unassigned function button)
Item Setting
F1: TCG Selects the timecode signal to which the
internal timecode generator
synchronizes.
INT
: Follow the initial value set from the
control panel or remotely from the
device connected to the
REMOTE(9P) connector, or
synchronize to timecode played
back from the disc.
EXT: Synchronize to external timecode
input to the TIME CODE IN
connector.
SDI: Synchronize to timecode
embedded into HDSDI signal input
to HDSDI INPUT connector.
F2: PRST/RGN Selects the following for the internal
timecode generator.
PRESET
: Presets an initial value for the
timecode generated by the internal
timecode generator, as specified
from the control panel or remotely
from the device connected to the
REMOTE(9P) connector. This is
valid when “INT” is selected with the
F1: TCG item on this page. The
operation is the same as “TC” when
anything else is selected.
TC: Generate timecode synchronized to
timecode read by the internal
timecode reader.
VITC: Generate timecode synchronized
to VITC read by the internal
timecode reader.
F3: RUN MODE Selects the timecode run mode.
FREE RUN: Timecode advances as long
as the unit is powered on, regardless
of the unit’s operating state.
REC RUN
: Timecode advances only
during recording. When you select
this item, also set F1: TCG on this
page to “INT” and set F2: PRST/
RGN to “PRESET”.
F4: DF/NDF Selects the drop-frame mode for the
internal timecode generator and the
counter in 59.94i mode.
DF
: Drop-frame mode
NDF: Non-drop-frame mode
F5: (Unassigned function button)
F6: TCR Selects the type of timecode to display in
the time data display area.
TC
: Display TC.
VITC: Display VITC.
Item Setting
