Filter
Top Products
9
Advanced Playback Operations
Note on the number indication in the display
The number indication in the display shows the number of
times you’ve pressed ) (or 0). During the deck is fast-
forwarding (or rewinding), the number decreases one by one to
indicate the number of tracks until the track you want to locate.
You can change the track you want to locate even
while the deck is in Multi-AMS operation
Press ) (or 0).
Notes
• The Multi-AMS function may not work correctly if:
— the blank space between tracks is less than 4 seconds
long.
— there is a passage of low frequencies or very low volume
within a track.
— the signal strength of the left and right channels are very
different.
• Even if DIR MODE is set to a, the deck stops when the
current side reaches the end during Multi-AMS operation.
• Do not turn on the Pitch Control function (see page 6) while
using the Blank Skip function on deck A. If you do, the
Blank Skip function may not work properly.
• Since the counter is not a digital clock, it will differ from the
actual elapsed playback or recording time.
Locating a Track (Multi-AMS/
Auto Play/Memory Play/Blank
Skip)
You can locate the following/previous tracks within a
range of 30 tracks (Multi-AMS: Automatic Music
Sensor) or the beginning of a tape quickly (Auto Play).
You can even locate a specific point anywhere on a
tape (Memory Play) or automatically skip over blank
spaces (Blank Skip).
Advanced Playback Operations
RESET 0/)
9/(
MEMORY
BLANK SKIP
0/)
9/(
9(
PHONE LEVEL
A -AUTO CAL-B
POWER
0
(AMS)
p
)
(AMS)
PRr
- RMS +
CLEAR BACK FRONT
PAUSE
§
OPEN/
CLOSE
RESET
PITCH CONTROL
SYNCHRO DUBBING A B
START P
MEMORY
COUNTER BA
RESET MEMORY
REC LEVEL
REC MUTE REC
ON/OFF
MPX FILTER
TIMER
OFF
REC PLAY
DIR MODE
p
PRr
PAUSE REC MUTE REC
DUBBING LEVEL
BALANCE
PHONES
4
7
1
BLANK SKIP
A -DOLBY NR-B
5
8
2
AUTO PAUSE
RMS / START DISPLAY
RMS
CHECK SET
6
9
A+B REC
10
HIGH
>10
NORMAL
+–
– +
3
§
OPEN/
CLOSE
START (DECK B P)
5
46
37
28
19
100
MAXMIN R
L
0
(AMS)
)
(AMS)
9(
Note
Check the direction indicator of the deck you use. When you
locate a track on the reverse side (when “ª” lights up), press
the button(s) in the parentheses.
Press
The beginning of the
next or succeeding
tracks
(Multi-AMS)
) (or 0) as many times as you
want during playback.
For example, to locate 2 tracks
ahead, press twice.
0 (or )) once during playback
0 (or )) as many times as you
want during playback.
For example, to locate 2 tracks
behind, press three times.
The beginning of the
preceding tracks
(Multi-AMS)
The beginning of a
tape (Auto Play)
The beginning of the
current track
(Multi-AMS)
MEMORY on the deck you’re using
repeatedly until “MEMORY”
disappears in the display. Then
press 0 (or )) while holding
down ( (or 9).
MEMORY on the deck you’re using
repeatedly until “MEMORY”
appears in the display. Find the
point you want, then press RESET to
reset the tape counter and to
memorize the point.
To locate the memorized point and
start playback, press 0 (or ))
while holding down ( (or 9).
(Press 0 or ) to stop at “0.00”.)
A particular point on a
tape (Memory Play)
BLANK SKIP until “BLANK SKIP”
appears in the display. Press again
to turn off the function when not in
use.
Tracks following
spaces of 13 seconds or
more (Blank Skip)
To locate