Filter
Top Products
Other Settings
13
65
En
English
Français
Deutsch
Nederlands
Italiano
Español
Dual Mono Setup
• Default setting:
CH1
You can specify how dual mono encoded Dolby
Digital and DTS soundtracks should be played.
Dual mono is not widely used, but is
sometimes necessary when two languages
need to be sent to separate channels.
1 Select ‘Dual Mono Setup’ from the Other
Setup menu.
2 Choose the setting that you want.
•
CH2
– Only channel 2 is played
•
CH1 CH2
– Both channels are played
through the front speakers
•
CH1
– Only channel 1 is played
3 When you're finished, press
RETURN
.
You return to the Other Setup menu.
LFE Attenuator Setup
• Default setting:
ATT 0 dB
Some Dolby Digital and DTS audio sources
include ultra-low bass tones. Set the LFE atten-
uator as necessary to prevent the ultra-low
bass tones from distorting the sound from the
speakers.
1 Select ‘LFE ATT Setup’ from the Other
Setup menu.
2 Choose the setting that you want.
•
ATT 0dB
– No limiting (recommended)
•
ATT 10dB
– 10 dB of limiting
•
LFE OFF
– No sound from LFE channel
3 When you're finished, press
RETURN
.
You return to the Other Setup menu.
SR+ Setup for Pioneer plasma displays
Make the following settings if you have
connected a Pioneer plasma display to this
receiver using an SR+ cable. Note that the
number of settings available will depend on the
plasma display you’ve connected.
See also
Using this receiver with a Pioneer
plasma display
on page 61.
1 Select ‘SR+ Setup’ from the Other Setup menu.
2 Select the ‘PDP Volume Control’ setting
you want.
•
OFF
– The receiver does not control the
volume of the plasma display
•
ON
– When the receiver is switched to one
of the inputs that use the plasma display
(
DVD/LD
, or another function below), the
volume on the plasma display is muted so
only sound from the receiver is heard.
3 Assign any input source connected to the
plasma display to the corresponding input
number.
This matches the receiver’s input source with a
numbered video input on the plasma display.
For example, assign
DVD/LD
to
input-2
if you
have connected your DVD video output to video
input 2 on the plasma display.
• The
Monitor Out Connect
should be set
to the input that you’ve used to connect
this receiver to your plasma display.
4 When you're finished, press
RETURN
.
You return to the Other Setup menu.
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR
+
Setup
Dual Mono [ CH1
6b.Dual Mono Setup
:Finish
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR
+
Setup
LFE ATT ATT 0dB
6c. LFE ATT Setup
:Finish
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR
+
Setup
PDP Volume Control
OFF
PDP Input Select
DVD/LD [ input-1 ]
TV/SAT [ input-2 ]
DVR [ input-3 ]
VIDEO [ TV ]
Monitor Out Connect
[ OFF ]
6d.SR
+
Setup
:Finish
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD input-1
TV/SAT input-2
DVR input-3
VIDEO TV
6d.SR
+
Setup
:Finish
[ ]
[ ]
[ ]
Monitor Out Connect
[ OFF ]
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD input-2
TV/SAT OFF
DVR input-3
VIDEO TV
6d.SR
+
Setup
:Finish
[ ]
[ ]
[ ]
Monitor Out Connect
[ OFF ]
VSX_916.book.fm 65 ページ ２００５年１２月２２日 木曜日 午後４時２１分