Filter
Top Products
Controlling the rest of your system11
52
En
• The remote controls should be 2 cm to 5
cm apart.
5 Press the corresponding button on the
other remote control that is sending
(teaching) the signal to this receiver’s remote
control.
For example, if you want to learn the playback
control signal, press and hold
for a couple of
seconds. The LCD display will show
OK
if the
operation has been learned.
If for some reasons the operation hasn’t been
learned the LCD will display
ERROR
briefly and
then display
PRES KEY
again. If this happens,
keep pressing the (teaching) button as you vary
the distance between the two remotes, until
the LCD display shows
OK
.
1
Certain buttons represent operations that
cannot be learned from other remote controls.
The buttons available are shown below:
6 To program additional signals for the
current component repeat steps 4 and 5.
To program signals for another component,
exit and repeat steps 1 through 5.
7 Press and hold the RECEIVER button for
two seconds to exit and store the
operation(s).
Erasing one of the remote
control button settings
This erases a control assigned to one of the
buttons and restores it to the factory default.
1 While pressing the RECEIVER button,
press the
SETUP
button.
The remote LCD display shows
SETUP
.
2 Use
/
to select
ERASE
then press
ENTER
.
The LCD on the remote displays the
component.
3 Press the MULTI CONTROL button
corresponding to the button setting to be
erased then press
ENTER
.
The remote LCD display flashes
PRES KEY
.
4 Press and hold the button to be erased for
two seconds.
The LCD display shows
OK
or
NO CODE
to
confirm the button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the RECEIVER button for
two seconds when you’re done.
Note
1• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer
together or farther apart.
• If the remote LCD shows
ERROR
, it may also mean the memory is full. See
Programming signals from other remote controls
below to erase a programmed button you’re not using to free up more memory.
2 cm to 5 cm
+
10
INPUT ATT FL DIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
SETUP
ENTER
TV CONTROL
RECEIVER CONTROL
SHIFT
VOL
DVD/LD TV/SAT DVR/VCRTV CONT
CD
TUNE
TUNE
ST ST
STANDRAD
LEVEL EFFECT
TEST TONE
CH SELECT
ADV. SURR STEREO SLEEP
INPUT
SELECT
TV CH
DTV ON/OFF
TUNER
DISPLAY
MPX
AUDIO
CH RETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
DTV INFOREC MUT E
TV VOL
CD-R/TAPE
TUNERRECEIVER
ENTER
REC STOP
HDD
CH
CH
DVD
D.ACCESS
TOP MENU
DTV MENU
CLASS
MENU
BAND
RETURN
GUIDE
T.EDIT
MCACC
SETUP
RECEIVER
ANALOG
AT T
MIDNIGHT/
LOUDNESS
SB ch
DIMMER
SLEEP
SR+
+10
D.ACCESS
DIALOG E
CLASS
DISC
RECEIVER
SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TUNE
TUNE
ST ST
ENTER
TOP MENU
PTY SEARCH
T. EDIT
MENU
RETURN
GUIDE
SETUP
TV DVR
TV CTRL
CD
RECEIVER
AMFM
DVD
CD-R/TAPE
USB
AV PRE-PROGRAMMED
AND LEARNING
REMOTE CONTROL UNIT
TV CONTROL
SHIFT
VOL
AUTO SURR
STANDARD ADV.SURR
S.RETRIEVER
SIGNAL SEL
STEREO
INPUT
SELECT
TV CH
MPX
A
B
CDE
EON
AUDIO
DISP
SUBTITLE
MULTI OPE
EFFECT/CH SEL
ACOUSTIC EQ
REC
MUTE
TV VOL
REC STOP JUKEBOX
HDD
CH CH
DVD
GUIDE
RECEIVER
VSX_916.book.fm 52 ページ ２００５年１２月２２日 木曜日 午後４時２１分