Filter
Top Products
Controlling the rest of your system
12
64
En
6 If necessary, press the input source button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input source).
7 Select the button for the command you want to
input.
The following remote control commands can be
selected:
• You don't need to program the receiver to switch on
or off. This is done automatically.
With Pioneer components
, you don’t need to:
• program the power to switch off in a shutdown
sequence (except DVD recorders);
• program the power to switch on if it’s the source
component selected in step 3;
• program a Pioneer TV or monitor to switch on if the
input function (selected in step 2) has video input
terminals;
These take priority in multi operations (not shutdown).
8 Repeat steps 5–7 to program a sequence of up to
five commands.
9 When you’re finished, use
/
to select EDITEXIT
from the menu and press
ENTER
.
You will return to the remote control
SETUP
menu. Select
* EXIT *
again to exit.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
1 Press MULTI OPE.
MULTI OP
flashes in the display.
2
Press
an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
Using System off
1 Press MULTI OPE.
MULTI OP
flashes in the display.
2 Press
SOURCE
.
The command sequence you programmed will run, then
all Pioneer components will switch off
1
, followed by this
receiver.
AV PRE-PROGRAMMED AND LEAR
NING
REMOTE CONTROL UNIT
ANALOG
AT T
MIDNIGHT/
LOUDNESS
VIDEO
SEL
DIMMER
SLEEP
SR+
+10
D.ACC ES S
DIALOG E
S.RETRIEVER
CLASS
DISC
RECEIVER
SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TUNE
TUNE
ST ST
ENTER
TOP MENU
AV PARAMETER CH LEVEL
PTY SEARCH
T. EDIT
MENU
RETURN
GUIDE
BAND
SETUP
TV DVR1
TV CTRL
iPod
RECEIVER
TUNERHDMI1
DVD
USBHDMI2
CD-R/TAPE
DVR 2CD
RECEIVER
TV CONTROL
SHIFT
VOL
STEREO
STATUS
SIGNAL SEL
THX
ADV.SURR
SBch
INPUT
SELECT
TV CH
MPX
A
B
CDE
EON
AUDI O
DISP
SUBTITLE
MULTI OPE
STANDARD
PHASE
S.DIRECT
MCACC
REC
MUTE
TV VOL
REC STOP JUKEBOX
HDD
CH
CH
DVD
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
RECEIVER
SHIFT
STEREO
STATUS
SIGNAL SEL
THX
ADV.SURR
SBch
AUDI O
DISP
SUBTITLE
MULTI OPE
STANDARD
PHASE
S.DIRECT
MCACC
HDD
CH
CH
DVD
AV PRE-PROGRAMMED AND LEAR
NING
REMOTE CONTROL UNIT
RECEIVER
INPUT
SELECT
TV DVR1
TV CTRL
DVD
DVR 2CD
SOURCE
SYSTEM OFF
RECEIVER
SHIFT
STEREO
STATUS
SIGNAL SEL
THX
ADV.SURR
SBch
AUDI O
DISP
SUBTITLE
MULTI OPE
STANDARD
PHASE
S.DIRECT
MCACC
HDD
CH
CH
DVD
VSX-2016_HY.book.fm 64 ページ ２００６年２月２４日 金曜日 午後１２時４０分